LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Renny Light Bar Installed, Windows Tinted, ETC>...
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=6&t=62894		 Page 1 of 1
Author:  Mr. eXtreme [ Thu Sep 29, 2011 4:53 pm ]
Post subject:  Renny Light Bar Installed, Windows Tinted, ETC>...
What do you think? First time I've had it off the road too!

Real happy with the light bar. Wasn't as much a pain in the A... as I heard to install.
Had front windows tinted to match the rears. Removed the vent shades that had been installed way to high.
Installed my washer bottle. Used factory location. Painted the bottle black.
Also cleaned, prepped and painted the axles, control arms, calipers, drums, etc with black caliper paint.
To keep things looking fresh.

Next on the list is LTT's CAI, after that it's hard to pick which thing to do next. LOL

BEFORE:
Image

AFTER:
Image
Image
Image
Image
Image
Image
Image
Image
Author:  gtommec [ Thu Sep 29, 2011 4:58 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
Looks good!! I can't believe how high those ventvisors were :shock: , Also do you have a Limited Edition badge under the sport badge on your doors? :?
Author:  Boomerang [ Thu Sep 29, 2011 5:23 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
nice job
Author:  Mr. eXtreme [ Thu Sep 29, 2011 5:31 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
gtommec wrote:
Looks good!! I can't believe how high those ventvisors were :shock: , Also do you have a Limited Edition badge under the sport badge on your doors? :?


Do I??? LOL Yeah I know. Those and the vent visors I still haven't figured out why...

I plan to strip all the badgging. Guy I bought it from gave me new ones.
Debating about just leaving them off all together or if I use the new ones scuffing them an painting them flat black before installing.
Author:  vincennescrd [ Thu Sep 29, 2011 11:12 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
I like the idea of painting badges but I would bedline them. But that's me
Author:  gtommec [ Thu Sep 29, 2011 11:28 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
since the badges are the gel-type and install like a decal, how would you paint them?
Author:  blackwidowkj06 [ Thu Sep 29, 2011 11:56 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
Looking good. Very simple KJ, but looks mean!

I'm getting TJ bumpers put on my KJ next week.
Author:  STINGN [ Fri Sep 30, 2011 12:18 am ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
where were you wheeling?!?!?!? im your neighbor and i didnt know of that spot!
Author:  Mr. eXtreme [ Fri Sep 30, 2011 1:45 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
gtommec wrote:
since the badges are the gel-type and install like a decal, how would you paint them?


They come on a paper backing. So my thought was to use some scotch brite pads or fine sandpaper and scuff the clear on them so paint or bedliner could adhere well.
I've used krylon fusion satin and flat black before on body moldings badges etc and it works an holds up really well if the services are prepped properly. It's made for plastics as well.
I did the bed rails and factory fender flares when I had my F150 and it held up to car washes and two winters no problem. Probably is still holding up but I sold the truck so can't confirm.
Author:  Mr. eXtreme [ Fri Sep 30, 2011 1:53 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
STINGN wrote:
where were you wheeling?!?!?!? im your neighbor and i didnt know of that spot!



LOL. What other spots do you know of??
Defanitly interested in learning of these.

It's right near were my folks live in McHenry the trails I beleve are what someone bulit at some point for there quads as allot of this area is or was farm land.
The area I'm flexing is actually the culvert of a neighborhood to be which backs up to farm and wet lands. I go there for photos and it's a good spot to get off the road lightly as long as respect the ground your on. There's some ruts, few hills, etc. I'll post up some shots of my 150 in same place.

The trails for the quads for the most part are wide enough for a Jeep kind of tight turns for a full size truck though. But is what you'd expect a ATV trail to look like!
Author:  gtommec [ Fri Sep 30, 2011 2:05 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
Mr. eXtreme wrote:
gtommec wrote:
since the badges are the gel-type and install like a decal, how would you paint them?


They come on a paper backing. So my thought was to use some scotch brite pads or fine sandpaper and scuff the clear on them so paint or bedliner could adhere well.


but like I said they install like a decal, which means that there is a clear plastic over the front of the emblem until it is put on the Jeep.
Author:  Mr. eXtreme [ Fri Sep 30, 2011 2:10 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
gtommec wrote:
Mr. eXtreme wrote:
gtommec wrote:
since the badges are the gel-type and install like a decal, how would you paint them?


They come on a paper backing. So my thought was to use some scotch brite pads or fine sandpaper and scuff the clear on them so paint or bedliner could adhere well.


but like I said they install like a decal, which means that there is a clear plastic over the front of the emblem until it is put on the Jeep.


Oh. Mine don't have the clear film over the faces of them. Maybe guy removed them.
I just have the paperbacking on them.

Guess if use some masking tape to keep a straight level line could install one part at a time.
Author:  Jaber [ Fri Sep 30, 2011 2:16 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
Very nice! I'm always nervous when it comes to drilling holes, so I'm putting the light bar off for a while lol...

Looks good with the tints, first thing I did when I bought mine :SOMBRERO: Only I got the back windows tinted to make it a bit darker and the two front are around 20%.
Author:  secondechomatt [ Fri Sep 30, 2011 4:09 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
Looks great! To cange the color of the decals without removing them AND able to go back to stock easily, use plasti-dip. Google "plasti-dip badges". Super easy.
Author:  vincennescrd [ Mon Oct 03, 2011 9:54 pm ]
Post subject:  Re: Renny Light Bar Installed, Windows Tinted, ETC>...
Sorry thought you were talking about the trail rated badges and such
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/