Got a few goodies added. Almost an AEV KJ....
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| AEV KJ ?? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=6&t=70149 |
Page 1 of 1 |
| Author: | brdl04 [ Thu Aug 16, 2012 8:13 pm ] |
| Post subject: | AEV KJ ?? |
Got a few goodies added. Almost an AEV KJ....
|
|
| Author: | infernicus [ Thu Aug 16, 2012 9:00 pm ] |
| Post subject: | Re: AEV KJ ?? |
|
|
| Author: | bigdogself [ Thu Aug 16, 2012 11:25 pm ] |
| Post subject: | AEV KJ ?? |
Looks good |
|
| Author: | Slava [ Fri Aug 17, 2012 3:59 pm ] |
| Post subject: | Re: AEV KJ ?? |
6.2 l? 
|
|
| Author: | At The Helm [ Sat Aug 18, 2012 12:05 am ] |
| Post subject: | Re: AEV KJ ?? |
Aw, i thought i was going to see a pickup bed kj. Looks great though. |
|
| Author: | arengant [ Sat Aug 18, 2012 10:00 am ] |
| Post subject: | Re: AEV KJ ?? |
Great stance! What lift/tire/wheel combo? |
|
| Author: | dejesu [ Thu Aug 23, 2012 9:27 am ] |
| Post subject: | Re: AEV KJ ?? |
arengant wrote: Great stance! What lift/tire/wheel combo? ^^ this |
|
| Author: | brdl04 [ Tue Sep 11, 2012 2:12 pm ] |
| Post subject: | Re: AEV KJ ?? |
OME 1.5 Lift with HD springs AEV TJ Pintler in Argent BFG Mud Terrain 255/75/17 Rubbing is pretty bad, needs quite a bit of trimming. |
|
| Author: | tommudd [ Tue Sep 11, 2012 4:11 pm ] |
| Post subject: | Re: AEV KJ ?? |
Need to add to the lift if you don't already have the 1/4 inch top plate and 3/8 inch clevis need about 4 inches of lift to run that size tire so you don't have to hack away at body parts PLUS of course .............REGEAR to 4.10s 
|
|
| Author: | surfRenegade [ Wed Sep 12, 2012 2:59 am ] |
| Post subject: | Re: AEV KJ ?? |
Chopping that front bumper lip is a good starting point to eliminate rub, then pound the pinch weld. I really like the look of your jeep though |
|
| Author: | teckman02 [ Wed Sep 12, 2012 5:00 pm ] |
| Post subject: | Re: AEV KJ ?? |
the wheels look good but i think that they kinda look a little odd on a jeep they look like they should be on a ferrari ro something |
|
| Author: | brdl04 [ Fri Sep 14, 2012 9:31 am ] |
| Post subject: | Re: AEV KJ ?? |
Hammered pinch weld. Trimmed and Trimmed. Still get slight rub at full turn. My next AEV mod will be a front/rear bumper. Suprisingly the JK AEV bumper is almost perfect size. |
|
| Author: | tommudd [ Fri Sep 14, 2012 10:36 am ] |
| Post subject: | Re: AEV KJ ?? |
What is the measurement from middle of the wheel to bottom of the flare in front ? |
|
| Author: | CoopaTroopa [ Fri Sep 14, 2012 10:55 am ] |
| Post subject: | Re: AEV KJ ?? |
I dont know how much it will help, but you could try to remove the fender linners if you haven't already. |
|
| Author: | brdl04 [ Wed Sep 19, 2012 9:38 am ] |
| Post subject: | Re: AEV KJ ?? |
I probably will need to remove the liner. I did slight trimming on the front of the wheel well, but the back of the well is the problem now. Its crazy though how much road noise I get from these tires. When you have them on a JK Rubicon from the factory you dont hear it too much...put them on a KJ and they whine like crazy. It must be the location of the tire more inside the body that the Wrangler. |
|
| Author: | tommudd [ Wed Sep 19, 2012 10:49 am ] |
| Post subject: | Re: AEV KJ ?? |
Instead of chopping more how about more lift, also back spacing can mess you up as well On those tires you have to keep them rotated every 3-4000 miles so they don't start cupping. Once they do lots more noise than normal still like to know bottom of fender to middle of wheel height 
|
|
| Author: | surfRenegade [ Fri Sep 21, 2012 3:31 pm ] |
| Post subject: | Re: AEV KJ ?? |
brdl04 wrote: My next AEV mod will be a front/rear bumper. Suprisingly the JK AEV bumper is almost perfect size. Oh man I have been dreaming about those bumpers. I cant wait to see how they look on a kj |
|
| Author: | mikey1273 [ Sun Sep 23, 2012 11:56 pm ] |
| Post subject: | Re: AEV KJ ?? |
love the wheels I can see just envision them on mine |
|
| Author: | tommudd [ Mon Sep 24, 2012 11:17 am ] |
| Post subject: | Re: AEV KJ ?? |
surfRenegade wrote: brdl04 wrote: My next AEV mod will be a front/rear bumper. Suprisingly the JK AEV bumper is almost perfect size. Oh man I have been dreaming about those bumpers. I cant wait to see how they look on a kj JK=good KJ=
|
|
| Author: | dgeist [ Tue Sep 25, 2012 11:05 am ] |
| Post subject: | Re: AEV KJ ?? |
Are we talking about this one:  That's going to be a lot of "adapting"...
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|