| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Skid Plate Question http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=65&t=60161 |
Page 1 of 1 |
| Author: | KTM87 [ Fri Apr 15, 2011 11:56 am ] |
| Post subject: | Skid Plate Question |
Hey for all of you that might have the mopar front suspension/engine skid plate, does anybody know what bolts sizes you use for that skid plate. I need to go pick them up and instead of dealing with the dealership to try in get the info i figure wouldnt hurt to ask on here first. So if anybody know some help would be appreciated 
|
|
| Author: | Khaki-KJ [ Fri Apr 15, 2011 10:23 pm ] |
| Post subject: | Re: Skid Plate Question |
They use nutzerts to mount the skid plates. If your Jeep came with skid plates, then the female part will already be in the crossmember and a quick phone call the a Chrysler parts counter should give you the bolt size. If you bought the skid plates from Jeep, then the nutzerts should have come with the skid plates. If they did not, then you will have to go to a Jeep / Chrysler dealer and get them. |
|
| Author: | Khaki-KJ [ Fri Apr 15, 2011 10:27 pm ] |
| Post subject: | Re: Skid Plate Question |
I just checked my Service manual and they do not give a bolt size for nutzerts, just torque specs. |
|
| Author: | gtommec [ Sat Apr 16, 2011 2:46 am ] |
| Post subject: | Re: Skid Plate Question |
I don't know about the 05 but the 02-04 KJ's only use nutzerts for the X-fercase skid. The engine skid plate (and the fuel tank skid for that matter) already have the threaded holes in them so you would just need to find the bolts. |
|
| Author: | KJ Willy [ Sat Apr 16, 2011 8:30 am ] |
| Post subject: | Re: Skid Plate Question |
Let me look, I think I may have some extras around, if you make it out to Steve's they should be there. |
|
| Author: | KTM87 [ Sat Apr 16, 2011 10:59 am ] |
| Post subject: | Re: Skid Plate Question |
KJ Willy wrote: Let me look, I think I may have some extras around, if you make it out to Steve's they should be there. Thanks Will unfortunately i wont beable to make it out to steves today  , but i got it all squared away i hope  Thanks for all the help guys |
|
| Author: | LibertyCRD [ Mon Apr 18, 2011 3:11 pm ] |
| Post subject: | Re: Skid Plate Question |
My front skid has 4 bolts. Two are 16mm, and two are 15mm. |
|
| Author: | tjkj2002 [ Mon Apr 18, 2011 8:55 pm ] |
| Post subject: | Re: Skid Plate Question |
The skid plate bolts for a KJ(front skid,trans,and t-case) are M10x1.50x30mm.The gas tank skid bolts are M12x1.75x40mm.All are metric grade 9.8,and 10.9's for the gas tank skid(a must). |
|
| Author: | bunkermonkeycw [ Mon Apr 18, 2011 11:36 pm ] |
| Post subject: | Re: Skid Plate Question |
I have two nuts welded inside my skid that line up with nothing, what can I attach to them? 
|
|
| Author: | KTM87 [ Tue Apr 19, 2011 6:07 pm ] |
| Post subject: | Re: Skid Plate Question |
bunkermonkeycw wrote: I have two nuts welded inside my skid that line up with nothing, what can I attach to them? The Boiler's Radiator Skid will match up with those Nuts that are welded, thats what i just installed. Thanks for all the replys, very helpful |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|