Hella 500s mounted to the base of the windshield pillar.
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Finally got them wired. http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=69&t=21480 |
Page 1 of 1 |
| Author: | priell3 [ Sat Jun 09, 2007 10:25 pm ] |
| Post subject: | Finally got them wired. |
Hella 500s mounted to the base of the windshield pillar.
|
|
| Author: | JJsTJ [ Sat Jun 09, 2007 10:40 pm ] |
| Post subject: | |
OW!  My Eyes! It Burns! 
|
|
| Author: | hyedipin [ Sat Jun 09, 2007 11:25 pm ] |
| Post subject: | |
Very nice, love the lights. 
|
|
| Author: | 05kjrenny [ Sun Jun 10, 2007 10:24 am ] |
| Post subject: | |
Nice, Ive got a friend with the same color jk looking to do some lights like yours, was the install hard to run the wires? Did you run them into the cowl cover? Any info would be good, I have KC slimlites on the Rubi but Im sure its a littl different install. |
|
| Author: | lilmatty [ Sun Jun 10, 2007 10:42 am ] |
| Post subject: | Re: Finally got them wired. |
priell3 wrote: Hella 500s mounted to the base of the windshield pillar.
Can you send along a pic of the mounting you used? |
|
| Author: | priell3 [ Sun Jun 10, 2007 2:04 pm ] |
| Post subject: | |
Full write-up and pics coming soon. Very easy install. |
|
| Author: | priell3 [ Sun Jun 10, 2007 11:25 pm ] |
| Post subject: | |
Mounting and wiring - The Hellas come with a U shaped bracket and I used this to mount the lights to the windshield pillar using the factory bolt. Protecting the paint is a cloth reinforced rubber washer (that I had laying around the house and is actually for toilet tank repair!). This mount is very secure. The lights are at a slight outward angle and project to the sides of the road and can only be adjusted up and down mounted this way. I'll be using them off-road so this works for me to light up the critters off to the sides of the road. I might get KC, Mopar or Warrior brackets at a later date. The other option was to mount them to the bumper but this method was required no drilling except for the hole for the switch in the dashboard. 
The wires run beneath the cowl and then an easy run into the engine compartment. 
I mounted the switch right above the left speaker in the dash board. Easy access behind it by removing the side panel. 
Wires run through firewall at this point in the upper left corner of the footwell. 
Wiring was connected following supplied instructions but instead of tapping high beam wire, I went straight off the positive battery terminal so that I could control them independently of the other lights. I might tap into the side marker lights later. I have wire loom on order to clean up the installation so ignore the clutter. None of the local stores had any. This was the first time I did this so if I can do it, anyone can! Just read the instructions several times, think through the installation and routing of the wires and ground points, and take your time. Plus, I asked alot of questions on the message boards. |
|
| Author: | JKinPA [ Thu Jun 14, 2007 1:45 pm ] |
| Post subject: | |
I call BS here! I know for a fact you didnt do this yourself! Prove it, Do mine 
|
|
| Author: | priell3 [ Thu Jun 14, 2007 4:09 pm ] |
| Post subject: | |
JKinPA wrote: I call BS here! I know for a fact you didnt do this yourself! Prove it, Do mine
Come on down! I take no responsibility for fried electrical systems. 
|
|
| Author: | hyedipin [ Thu Jun 14, 2007 4:11 pm ] |
| Post subject: | |
How did you mount the switch like that? 3M around edges with a small hole for the wires. ? |
|
| Author: | priell3 [ Thu Jun 14, 2007 5:14 pm ] |
| Post subject: | |
hyedipin wrote: How did you mount the switch like that? 3M around edges with a small hole for the wires. ?
Drilled 1/2" hole through plastic. Knurled part screws to post on back of switch securing it to dash. 
|
|
| Author: | hyedipin [ Thu Jun 14, 2007 9:45 pm ] |
| Post subject: | |
Oh, so that's how it secures in the back! Thanks Mike ! PS: Man, everytime I recall your name, priell, I remember the skull on the flipper and your nice black KJ. Pls put it back to your new jeep and get back to your roots... 
|
|
| Author: | AbsoluteRenegade [ Thu Jun 14, 2007 10:11 pm ] |
| Post subject: | want it! |
I posted somewhere about doing this to my renegade. Anyone do this to a KJ? |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|