| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Yukon Gearing http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=73&t=45466 |
Page 1 of 1 |
| Author: | JeepBumm68 [ Fri Jul 31, 2009 10:01 am ] |
| Post subject: | Yukon Gearing |
From what i have heard is that Yukon makes the only 8.25 gearing that does not grind, and make any noise at all. they have perfected the 8.25 ring and pinion gear set. Good way to go. Already tested this out in my buddies xj, that had g2's, presicion, and a few others in it, and the yukon gearing slipped right in no issuses and no noises on the road. |
|
| Author: | ohv_kj [ Fri Jul 31, 2009 1:46 pm ] |
| Post subject: | |
is there a question or is this a testement to yukon :skep: |
|
| Author: | TAHOE [ Fri Jul 31, 2009 2:07 pm ] |
| Post subject: | |
I put a set of 7.65" Yukons 4.10's in my old Astro, slid right in, perfect settings on 1st shot, never any noise, wore great. I would buy them again for another vehicle. |
|
| Author: | JeepBumm68 [ Fri Jul 31, 2009 9:54 pm ] |
| Post subject: | |
I am saying this ohv. testament pretty much |
|
| Author: | Inc [ Fri Jul 31, 2009 10:55 pm ] |
| Post subject: | |
If you are going to run 4.88s there is only one company that makes them and it isn't Yukon. Google 4.88 gears for the Chrysler 8.25. If you are going 4.56s then you have better options. |
|
| Author: | JeepBumm68 [ Sat Aug 01, 2009 4:05 pm ] |
| Post subject: | |
you are correct. for the 8.25 they don't go up to 4.88's. so i'll be doing 4.56's in the liberty then. With those matched with the deisel motor it wel have plenty of power |
|
| Author: | Inc [ Sat Aug 01, 2009 4:30 pm ] |
| Post subject: | |
JeepBumm68 wrote: you are correct. for the 8.25 they don't go up to 4.88's. so i'll be doing 4.56's in the liberty then. With those matched with the deisel motor it wel have plenty of power
I was lucky and only had to get the rear gears. The 4.88s came with my Dana 30 so I only needed to get them for my Chr. 825. I would think the 4.56 would work well with a diesel. |
|
| Author: | hiram [ Sat Aug 01, 2009 9:05 pm ] |
| Post subject: | yukon |
i run yukon on my jeep and love them! |
|
| Author: | ohv_kj [ Sun Aug 02, 2009 10:50 am ] |
| Post subject: | |
Inc wrote: If you are going to run 4.88s there is only one company that makes them and it isn't Yukon. Google 4.88 gears for the Chrysler 8.25. If you are going 4.56s then you have better options.
ahh...but like anything else...the 4:88 by nitro are re-badge yukons... i deal w/ east coast gear supply as my gear person at the shop...straight out of the horses mouth... |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|