Those rims are like a flat black or matte.
You can go to Summit Racing and look at what they have
just make sure you are looking at the right size, backspacing,width
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Market for New steel http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=8&t=53614 |
Page 1 of 1 |
| Author: | Vranes17 [ Thu Jun 17, 2010 9:09 pm ] |
| Post subject: | Market for New steel |
So I think I may want to get some new rims. Saw these they are like the soft 8s but dont fit. http://www.desertrat.com/images/?id=6450 I really like the look/color of that rim. What would you call that color? Charcol? Is there a place where I can look at rims that will fit the liberty all in one spot, or must i look for a rim with the correct specs? Also I noticed on my truck after i switched from ATs to MT's about a month or so ago, I got squeeking from the brakes. This only happens at low speed while the car hasnt been driven long ,ie. pulling out of the driveway. Its very annoying, can i do anything? |
|
| Author: | tommudd [ Thu Jun 17, 2010 9:40 pm ] |
| Post subject: | Re: Market for New steel |
Those rims are like a flat black or matte. You can go to Summit Racing and look at what they have just make sure you are looking at the right size, backspacing,width
|
|
| Author: | TAHOE [ Thu Jun 17, 2010 10:04 pm ] |
| Post subject: | Re: Market for New steel |
Those are the same type I have on my Tahoe, just in the coated gray, look like the teflon coated ones.... sharp though. Too bad they won't fit for ya. |
|
| Author: | jimymc [ Thu Jun 17, 2010 10:22 pm ] |
| Post subject: | Re: Market for New steel |
The squeaking you hear from your brakes is probably rust on the rotors. My Honda CRV is really bad about that. Let it sit in our Florida humidity for a couple of days without driving it and the first time or two you apply the brakes it will grind and squeak. After the first time or so of using the brakes the rust is cleared away and they won't do it anymore until it is left alone for a few days again or until it rains for awhile. |
|
| Author: | Vranes17 [ Fri Jun 18, 2010 1:54 pm ] |
| Post subject: | Re: Market for New steel |
Liberty Wheel Specs 16x7 Bolt Pattern: 5x4.5" Backspacing: 5.5" Offset: 38mm That is what my limited has correct? When I do a search for rims, I see the Soft 8's have 4" BS what is the lowest I should look at? What about as far as the Offset? Would any of this require a spacer? |
|
| Author: | DirtyKK [ Fri Jun 18, 2010 2:00 pm ] |
| Post subject: | Re: Market for New steel |
for a 7" rim a 4" backspacing is good or a 16x8 with 5" bs |
|
| Author: | Vranes17 [ Fri Jun 18, 2010 6:04 pm ] |
| Post subject: | Re: Market for New steel |
my 245/75/16 can fit on a 16x8 rim? |
|
| Author: | Powerman04 [ Fri Jun 18, 2010 6:41 pm ] |
| Post subject: | Re: Market for New steel |
Sure can. I'm going to be putting my 245/70's on 16x8's in short time. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|