Curious is anyone is running this setup and will it/does it minimize rubbing?

Thanks,

Mike

_________________
'06 CRD
Frankenlift II, 245/75/16 Goodyear MT/R's on Moabs, Samco Hoses, Provent, Mopar iPod Integration Kit

Ran them for a while
are you lifted ?

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

Yeah, OME lift. HD springs up front, MED spring rate in rear. OME shocks and struts as well.

_________________
'06 CRD
Frankenlift II, 245/75/16 Goodyear MT/R's on Moabs, Samco Hoses, Provent, Mopar iPod Integration Kit

Should have no issues then
I'll try and find a couple of pictures for ya

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

depending on the tread width (different from section width)
you might end up hammering down a pinch weld and clearing up some of the front wheel well liner

or it may clear with no issues......

normally 255's are not a problem.

_________________
2005 CRD
stuff
Skeptic quod gratis asseritur, gratis negatur

Thanks for the advice. I currently have 245/75/16's on the Moabs now and they rub on both the lower front bumper trim strip and the pinch weld, or at least the inner fender liner over the welds. I have to look at them some more. Another question, what tire pressure do people run the tires at? I know the max is 80 psi on the MT/R's I have on there now. Usually, with the previous tires the max was 50 psi and I ran them around 45 psi cold.

Thanks.

_________________
'06 CRD
Frankenlift II, 245/75/16 Goodyear MT/R's on Moabs, Samco Hoses, Provent, Mopar iPod Integration Kit

Hey! I see you're from Allentown. Howdy neighbor!!!

_________________
2010 Liberty Sport, Command Trac 4x4
Rock Krawler 3.5 Inch X Factor Lift
Skyjacker H7071 rear shocks,
245/75R16 Firestone Destination A/T

Here's a pic with the wheels and tires mounted on the jeep.

Moabs with 245/75/16 Goodyear MT/R's on them.

_________________
'06 CRD
Frankenlift II, 245/75/16 Goodyear MT/R's on Moabs, Samco Hoses, Provent, Mopar iPod Integration Kit

I run 255/70-16's on stock Renegade wheels. No rub except in reverse at full lock on the edge of the front air dam. Lifted sitting at 22.25 front, 22.5 rear with OME 927/948, 1/4" top plate, 3/8" clevis and one extra rear iso. You should be OK but with the backspacing difference I don't know if you'd catch the fog light door and/or the pinch weld cuz of the wider arc.




Bob

_________________
2003 Liberty
- 3.7L V6, NP242 SelecTrac Transfer Case
- OME 927/948's, Bilsteins, JBA Gen 4.5 A-arms, JBA 1/4" top plate, 3-ring clevis, 2 extra rear isos
- Rubicon Moabs
- 4.10's, 265/70-16 Goodyear Duratracs
- 4X Guard Trans Skid, Modded BoulderBars, Mopar Engine, T-Case, Tank Skids, ARB bumper, Smittybilt 9500XRC winch