It is currently Sat Nov 17, 2018 6:21 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Black Rock wheel question
PostPosted: Fri Jan 23, 2015 10:27 pm 
Offline
LOST Newbie

Joined: Fri Jan 23, 2015 10:19 pm
Posts: 23
Location: San Pedro, CA
I have the OME spring lift for my CRD KJ.

Also have 31x10.5 15 Duratracs on order and want the following wheels which are 15x7 with 4.5" back spacing. Obviously 5 bolt by 4.5.
http://www.jeep4x4center.com/black-rock ... 71242.html

How do I know if these wheels will fit over the calipers? I've read it's hit and miss with the 15" wheels.

_________________
2005 KJ CRD
Frankenlift + plate
31x10.5x15 Duratracs
15x7 Black Rock Jack 929 w/ 4.5" BS
Powerstop drilled/slotted rotors/ pads
Wells/ bumper cut. Pinch welds. DIY bed liner'd Crossbars and grill. 8,000lb hitch. Tint. Debadge. Thule. Kenwood DDX470
Muffler delete. ORM

Weekend: 2008 135i. 400rwhp/ 450rwtq. 3,100lbs


Top
 Profile  
 
 Post subject: Re: Black Rock wheel question
PostPosted: Sat Jan 24, 2015 8:48 pm 
Offline
Moderator / Lifetime Member
Moderator / Lifetime Member

Joined: Thu Jul 07, 2005 5:49 pm
Posts: 27796
Location: Central Ohio/ Tanzania
Balance156 wrote:
I have the OME spring lift for my CRD KJ.

Also have 31x10.5 15 Duratracs on order and want the following wheels which are 15x7 with 4.5" back spacing. Obviously 5 bolt by 4.5.
http://www.jeep4x4center.com/black-rock ... 71242.html

How do I know if these wheels will fit over the calipers? I've read it's hit and miss with the 15" wheels.


Should fit OK, its mainly stock 15 inch wheels where there is problems, aftermarket not so much

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 Goodyears/ 4.10's etc, 04 Kilimanjaro Edition loaded


Top
 Profile  
 
 Post subject: Re: Black Rock wheel question
PostPosted: Sun Jan 25, 2015 3:16 pm 
Offline
LOST Newbie

Joined: Fri Jan 23, 2015 10:19 pm
Posts: 23
Location: San Pedro, CA
Thanks, Tom. I see you have Duratracs... Any advice on rotation rate and pattern? I have 5 on order.

_________________
2005 KJ CRD
Frankenlift + plate
31x10.5x15 Duratracs
15x7 Black Rock Jack 929 w/ 4.5" BS
Powerstop drilled/slotted rotors/ pads
Wells/ bumper cut. Pinch welds. DIY bed liner'd Crossbars and grill. 8,000lb hitch. Tint. Debadge. Thule. Kenwood DDX470
Muffler delete. ORM

Weekend: 2008 135i. 400rwhp/ 450rwtq. 3,100lbs


Top
 Profile  
 
 Post subject: Re: Black Rock wheel question
PostPosted: Mon Feb 02, 2015 1:42 am 
Offline
LOST Newbie

Joined: Fri Jan 23, 2015 10:19 pm
Posts: 23
Location: San Pedro, CA
Got the wheels and tires on and took her out for some serious wheelin'... Flexing it as much as possible. Trimmed a lot :)

Wheels fit perfectly. Zero issues fitting calipers in them. Extremely happy with my choice. Also haven't seen a liberty with these wheels other than mine :D

_________________
2005 KJ CRD
Frankenlift + plate
31x10.5x15 Duratracs
15x7 Black Rock Jack 929 w/ 4.5" BS
Powerstop drilled/slotted rotors/ pads
Wells/ bumper cut. Pinch welds. DIY bed liner'd Crossbars and grill. 8,000lb hitch. Tint. Debadge. Thule. Kenwood DDX470
Muffler delete. ORM

Weekend: 2008 135i. 400rwhp/ 450rwtq. 3,100lbs


Top
 Profile  
 
 Post subject: Re: Black Rock wheel question
PostPosted: Mon Feb 02, 2015 11:40 am 
Offline
Moderator / Lifetime Member
Moderator / Lifetime Member

Joined: Thu Jul 07, 2005 5:49 pm
Posts: 27796
Location: Central Ohio/ Tanzania
Balance156 wrote:
Got the wheels and tires on and took her out for some serious wheelin'... Flexing it as much as possible. Trimmed a lot :)

Wheels fit perfectly. Zero issues fitting calipers in them. Extremely happy with my choice. Also haven't seen a liberty with these wheels other than mine :D


I have over 84,000 on the Duratracs now. Rears straight up to the front, fronts crossed over to the rear ( left front becomes right rear etc ) Do you have bumpstops in, shouldn't be any or not much trimming except for pounding over the pinchweld

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 Goodyears/ 4.10's etc, 04 Kilimanjaro Edition loaded


Top
 Profile  
 
 Post subject: Re: Black Rock wheel question
PostPosted: Tue Feb 03, 2015 2:28 am 
Offline
LOST Newbie

Joined: Fri Jan 23, 2015 10:19 pm
Posts: 23
Location: San Pedro, CA
Had to trim a decent amount out of the front of the inner front fender wells. Had issues cranking wheels in reverse over my steep driveway apron. Attacked it again with the dremel tonight and it's all fixed up now. Zero rubbing.

Once I figure out how to post pics I'll put a bunch up. Looking forward to showing off the rig.

And the Duratracs are amazing. I had zero tire noise and they have a high level of grip on and off road.

_________________
2005 KJ CRD
Frankenlift + plate
31x10.5x15 Duratracs
15x7 Black Rock Jack 929 w/ 4.5" BS
Powerstop drilled/slotted rotors/ pads
Wells/ bumper cut. Pinch welds. DIY bed liner'd Crossbars and grill. 8,000lb hitch. Tint. Debadge. Thule. Kenwood DDX470
Muffler delete. ORM

Weekend: 2008 135i. 400rwhp/ 450rwtq. 3,100lbs


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com