What have you done to your KK lately

Gageraid · **Posted:** Sat Mar 15, 2014 11:28 pm

Who owns the red KK? Looks lifted.

JeepNCrowd · **Posted:** Sat Mar 15, 2014 11:38 pm

Gageraid wrote:

Who owns the red KK? Looks lifted.

His name is Adrian. He's got a JBA 4" on 31" wrangler MTRs.
It was a great run with no reported trail damage, yet. My rotors (at least that's what I think is causing it) are still screeching after I tried hosing them down to clear any mud or rocks that may have gotten in there. Oh well breaks still work fine. This had happened before. Hopefully it'll just go away like it did the few times it happened before. Its just v really annoying.

Gageraid · **Posted:** Sat Mar 15, 2014 11:45 pm

JeepNCrowd wrote:

Gageraid wrote:

Who owns the red KK? Looks lifted.

His name is Adrian. He's got a JBA 4" on 31" wrangler MTRs.
It was a great run with no reported trail damage, yet. My rotors (at least that's what I think is causing it) are still screeching after I tried hosing them down to clear any mud or rocks that may have gotten in there. Oh well breaks still work fine. This had happened before. Hopefully it'll just go away like it did the few times it happened before. Its just v really annoying.

Does it while driving or braking?
I had an issue once that would only screech in reverse. Turned out to be a little rock stuck in the rear passenger side rotor. Take off the wheels and inspect if you haven't already.
Is your buddy a member here? All hail those who have JBA 4 inch lift. :JEEPIN:

JeepNCrowd · **Posted:** Sat Mar 15, 2014 11:55 pm

Ya, he's red08kk. But I don't think he's posted on the forums yet.
Doesn't really do it when I brake, but mostly between 5-20 mph. It probably still does it at higher speeds but the tire, wind, and engine noise covers it up.

Gageraid · **Posted:** Sun Mar 16, 2014 1:44 am

JeepNCrowd wrote:

Ya, he's red08kk. But I don't think he's posted on the forums yet.
Doesn't really do it when I brake, but mostly between 5-20 mph. It probably still does it at higher speeds but the tire, wind, and engine noise covers it up.

Check out the rotors very closely. I didn't understand how my noise was only in reverse, but didn't question it when I found that rock. That was not a good day.

Bmxer524 · **Posted:** Sun Mar 16, 2014 4:18 am

I had a rock stuck in the calipers a few times. The first I couldn't find, dad helped me sort that out. The second time it was the same sound pulled over and did a 3 point turn. When stepping on the brakes it broke the rock and cleared it...

TIJKK1220 · **Posted:** Sun Mar 16, 2014 1:36 pm

Check out these poser shots lol

Sent from my HTC One using Tapatalk

silverkk · **Joined:** Mon Feb 04, 2013 12:27 pm **Posts:** 637

silverkk · **Joined:** Mon Feb 04, 2013 12:27 pm **Posts:** 637

Xj retro fit bumper

silverkk · **Joined:** Mon Feb 04, 2013 12:27 pm **Posts:** 637

ok so this is a company selling this as a kit same bumper and all mounting components should work with ours cuz nitro and the kk are the same unibody

LKWJeeper · **Posted:** Sun Mar 16, 2014 8:23 pm

That's awesome!

Sent from my LG-D801 using Tapatalk

At The Helm · **Posted:** Sun Mar 16, 2014 8:30 pm

The mounts would be the same but that's about it. The grille, fender flares, and turn signals are totally different. (The turn signals are mounted to the factory bumper) It would take a lot if work to make a KA bumper fit a KK. Glad to see the KA finally get a bumper though, looks good.

silverkk · **Joined:** Mon Feb 04, 2013 12:27 pm **Posts:** 637

It's a jk bumper

silverkk · **Joined:** Mon Feb 04, 2013 12:27 pm **Posts:** 637

With just brackets that allow you to mount any jk bumper

hydenphoto · **Posted:** Sun Mar 16, 2014 11:14 pm

silverkk wrote:

I would like to see more pics of the hood brackets for the shovel, and light brackets. Please post more pics!!!!

The bumper looks great. Fenders????? Turn signal????
Can't wait to see more!

silverkk · **Joined:** Mon Feb 04, 2013 12:27 pm **Posts:** 637

hydenphoto wrote:

silverkk wrote:

I would like to see more pics of the hood brackets for the shovel, and light brackets. Please post more pics!!!!

The bumper looks great. Fenders????? Turn signal????
Can't wait to see more!

He's keeping the fenders flares off and the blinkers are back on I made the light mounts and sent him how to make them and he did the shovel mount

There's a quick pic of the light mounts pm for questions

rangerr47 · **Joined:** Thu Jan 10, 2013 3:03 pm **Posts:** 71

silverkk wrote:

With just brackets that allow you to mount any jk bumper

So your saying these guys are selling a kit that is brackets that will let you put a JK bumper on a Liberty? And its solid? As in not just rigged up to put it on, but actually on there and ready for battle?

silverkk · **Joined:** Mon Feb 04, 2013 12:27 pm **Posts:** 637

Yes I am And you can only get one bumper but the brackets come with it

Cainneach · **Posted:** Mon Mar 17, 2014 11:02 pm

silverkk wrote:

ok so this is a company selling this as a kit same bumper and all mounting components should work with ours cuz nitro and the kk are the same unibody

That thing is pretty sick looking!

toy4everyseason · **Posted:** Tue Mar 18, 2014 3:05 am

silverkk wrote:

ok so this is a company selling this as a kit same bumper and all mounting components should work with ours cuz nitro and the kk are the same unibody

Ok so I did some searching on that bumper. The company says it fits JK but shows it mounted on a KA. He mentioned in a Twitter or instagram post that he had to cut off the winch plate to make it fit so that's a little concerning. Here's the kicker...$415 shipped for a winch bumper. At that price I'll make it fit. I'm going to try to contact that company to try to get a picture of the back side of the bumper. Here's the link
http://www.customwheeloffset.com/custom ... -jk-bumper

What have you done to your KK lately

Who is online