KK fender flares/ Extenders

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

I need to know where i can get Fender Flares for my 2012 Liberty KK. I want to remove my front bumber and make a custom one in my shop but I need to know where i can get the fender flares first so i can price em out and order em. Any ideas? I have been to a few sites already and im not having much luck. im on a 24 hour shift and not a lot going on so im searching!

tommudd · **Posted:** Fri May 25, 2012 12:33 pm

Aftermarket, there isn't any
Stock have to go to a dealer

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

So, just to make sure im reading that right. there are no stock ones only aftermarket. or there are only stock ones and not any aftermarket. How difficult would it be to make my own. i do have a fab shop back in alaska.

CoopaTroopa · **Posted:** Fri May 25, 2012 1:49 pm

There are stock ones that you can get from your dealership, but no one makes any after market replacements.

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

Yea im trying to change the design I want to Put a custom bumper on but i feel that the fenders will stick down lower than the bumper so i figure new fenders may make it easier to customize the bumper the way i want

CoopaTroopa · **Posted:** Fri May 25, 2012 1:57 pm

You could trim the flares like people do with arb bumpers.

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

I have thought about that but my only concern is if i wanted to return it to factory settings later on. I am military so im trying to keep my vehicle versatile to be changed to my different duty stations. I may have no other option but to trim them i was just hoping to be able to find some new ones that are already what i want. Is it possible to just make my own and if so how hard do you think itd be?

CoopaTroopa · **Posted:** Fri May 25, 2012 2:34 pm

Honestly I have no idea how difficult it would be to make your own, but a good guy to pm and ask about it would be kjwildman, he made his own and they look great.

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

I just went and saw the post about his fenders and saw the pictures of the entire production and i must say that is creative. i think im going to do the same when i get back to the states

At The Helm · **Posted:** Fri May 25, 2012 3:43 pm

Angle grinder zips right through em :wink:

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

i like how you got em to sit so flush. trial and error? or did you just do the math?

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

no winch on the front? Another thing im interested in is getting a winch that i can mount in my receiver and power off my trailer power. what you think?

At The Helm · **Posted:** Fri May 25, 2012 4:54 pm

The bottom of the grille is is a straight line and the flares are cut to match that line.

I didn't and don't have the $$ for a winch, but i can easily modify my bumper for one if i ever want to.

Are you talking about your trailer wire harness? If so, no way. Winches should come with a wire kit and use a heavy gauge wire directly to your battery.

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

I wonder if i can wire it up and have a quick disconnect then, like for my trailer hook up. just have it sit near that and then i can disconnect and use when needed?

At The Helm · **Posted:** Fri May 25, 2012 5:12 pm

Not sure about what to do for wiring on a rear hitch mount winch. You could probably run zero gauge all the way back there, but i couldn't say for sure.

Sgtski12 · **Joined:** Thu May 24, 2012 12:21 pm **Posts:** 20

I have about 60 mechanics and a whole group of electronic repair people in my unit that i can always get to work that out. I just like the idea of being able to run my winch from my vehicle or just take it off and throw it on someone elses to have em pull themselves out in case i cant get to em. probably looking at a completely detatchable system. wiring and all.

Ted15 · **Posted:** Sun May 27, 2012 9:38 am

Sgtski12 wrote:

I have about 60 mechanics and a whole group of electronic repair people in my unit that i can always get to work that out. I just like the idea of being able to run my winch from my vehicle or just take it off and throw it on someone elses to have em pull themselves out in case i cant get to em. probably looking at a completely detatchable system. wiring and all.

Welding cable should work. That and snowplow plugs.

musclezmarinara · **Posted:** Sun May 27, 2012 11:47 am

Stock replacements are like 700 bucks ouch

Musclez Marinara
Marco@acor4x4.com

teckman02 · **Posted:** Sun May 27, 2012 2:16 pm

It would not hurt to sent bushwacker a email they just made some for the WJ grand maybe if they get enough people want some they may start to make them

musclezmarinara · **Posted:** Wed May 30, 2012 11:29 pm

Atthehelm wrote:

Angle grinder zips right through em :wink:

atthehelem I WANT THAT BUMPER :BANANA:

KK fender flares/ Extenders

Who is online