| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| JBA Bump Stop Install Assistance> http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=88&t=66321 |
Page 1 of 1 |
| Author: | musclezmarinara [ Mon Apr 09, 2012 11:11 pm ] |
| Post subject: | JBA Bump Stop Install Assistance> |
Hey guys my ome setup is all set and installed got a set of the JBA Rear Red Bump Stops, but there is no place to mount these guys....any assistance? |
|
| Author: | At The Helm [ Mon Apr 09, 2012 11:37 pm ] |
| Post subject: | Re: JBA Bump Stop Install Assistance> |
They go on the lower spring seat. You'll have to remove the rear springs to drill the hole. Here's a write up from Budke at kjcountry: http://www.jeepkj.com/forum/f202/how-in ... ion-43989/ |
|
| Author: | DirtyKK [ Tue Apr 10, 2012 12:20 am ] |
| Post subject: | Re: JBA Bump Stop Install Assistance> |
you have to drill a hole in the spring mount. those bump stops were terrible imo. my upper stop would only half way hit the lower stop and wasnt limiting travel enough. i went with zone bump stops and carriage bolts. i used the carriage bolts because regular hex head hardware was tearing up the oem upper stops. |
|
| Author: | musclezmarinara [ Tue Apr 10, 2012 10:32 am ] |
| Post subject: | Re: JBA Bump Stop Install Assistance> |
DirtyKK wrote: you have to drill a hole in the spring mount. those bump stops were terrible imo. my upper stop would only half way hit the lower stop and wasnt limiting travel enough. i went with zone bump stops and carriage bolts. i used the carriage bolts because regular hex head hardware was tearing up the oem upper stops. Better off with those? or leave stock in? |
|
| Author: | At The Helm [ Tue Apr 10, 2012 10:52 am ] |
| Post subject: | Re: JBA Bump Stop Install Assistance> |
musclezmarinara wrote: DirtyKK wrote: you have to drill a hole in the spring mount. those bump stops were terrible imo. my upper stop would only half way hit the lower stop and wasnt limiting travel enough. i went with zone bump stops and carriage bolts. i used the carriage bolts because regular hex head hardware was tearing up the oem upper stops. Better off with those? or leave stock in? The stock orange colored bump stops stay where they are. Esp with your 32s i would run them. |
|
| Author: | KK_Canuck_Guy [ Tue Apr 10, 2012 2:24 pm ] |
| Post subject: | Re: JBA Bump Stop Install Assistance> |
musclezmarinara wrote: Hey guys my ome setup is all set and installed got a set of the JBA Rear Red Bump Stops, but there is no place to mount these guys....any assistance? SOoo...curious...any pics with the 32's?? Looking forward to seeing them 
|
|
| Author: | musclezmarinara [ Tue Apr 10, 2012 4:26 pm ] |
| Post subject: | Re: JBA Bump Stop Install Assistance> |
KK_Canuck_Guy wrote: musclezmarinara wrote: Hey guys my ome setup is all set and installed got a set of the JBA Rear Red Bump Stops, but there is no place to mount these guys....any assistance? SOoo...curious...any pics with the 32's?? Looking forward to seeing them not yet :/ |
|
| Author: | norcalarctic [ Thu Apr 12, 2012 8:27 pm ] |
| Post subject: | Re: JBA Bump Stop Install Assistance> |
Speaking of rear bump stops, any pics or info on hockey pucks that some of you have installed. Getting my OME + 1 top isos. lift finally done next week. Do I need extra bump stops besides the factory ones for this lift in rear? Also, one or two pucks? Only stepping up one size to a 245/75/16 tire. I got Terra Flex bump stops for the front already. Thanks |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|