| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Matrix brush guard on a KK? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=88&t=72301 |
Page 1 of 2 |
| Author: | KK4x4 [ Mon Oct 29, 2012 2:01 pm ] |
| Post subject: | Matrix brush guard on a KK? |
Does anyone know if the matrix brush guard for the kj on the jeepinbyal site will fit the KK? |
|
| Author: | At The Helm [ Mon Oct 29, 2012 2:19 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
The front end sheet metal is the same for kk/kj. Problem is the plastic is way different, so it might not look the way it was designed to and you might have to cut a lot of your bumper. Question is, why would you want that thing when there is a real bumper available? |
|
| Author: | KK4x4 [ Mon Oct 29, 2012 2:23 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
Less weight up front but if a lot of the bumper needs to be trimmed then I'd rather go the full bumper and hd springs |
|
| Author: | tommudd [ Mon Oct 29, 2012 4:48 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
I have one sitting here waiting to try I had it to try and see how it worked on the 05-07 KJs and was hoping to try it next on a KK Will let you know as soon as I do. I think it would work all except the receiver part but not 100% sure |
|
| Author: | Sagerist [ Tue Oct 30, 2012 1:02 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
Atthehelm wrote: Question is, why would you want that thing when there is a real bumper available? When did that Happen??????? and who is making them? last i heard Mtnluvr was in no man's land and no one else really wanted to make them except for the guys who made it themselves. |
|
| Author: | Cherrie 274 [ Tue Oct 30, 2012 3:08 pm ] |
| Post subject: | Matrix brush guard on a KK? |
I think his talking about his. viewtopic.php?p=750367#p750367 |
|
| Author: | Wearyman [ Tue Oct 30, 2012 3:54 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
There is this one too: Big Tube Bar |
|
| Author: | Sagerist [ Tue Oct 30, 2012 4:12 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
ahhhhhhh..... I didnt know he actually went out and finally made it!! i remember him putting the card board pieces together and talking about doing the metal prototype version, but havent been paying attention enough to the forum's to keep up on the progress. Good work Atthehelm!! Sooner or later i will be putting one of these on the Jeep. Need to get thru a wedding and get the OME lift first....darn priorities. |
|
| Author: | Cherrie 274 [ Tue Oct 30, 2012 4:19 pm ] |
| Post subject: | Matrix brush guard on a KK? |
Wearyman wrote: There is this one too: Big Tube Bar well that looks like a TMJ(?) bumper! It seems to be on a right hand drive and a "Cherokee", so I'm thinking overseas? |
|
| Author: | At The Helm [ Tue Oct 30, 2012 4:50 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
I am ready to make more, just nobody seems to actually want to buy them and wait for me to make them one. I'm picking up some more steel tomorrow, there will probably be a front and rear bumper ready to buy in a couple of months if anyone is interested. |
|
| Author: | At The Helm [ Tue Oct 30, 2012 5:11 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
Wearyman wrote: There is this one too: Big Tube Bar Seems kinda backwards though, a low hanging bumper on top of a bumper? What? |
|
| Author: | tommudd [ Tue Oct 30, 2012 5:46 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
Like it The Aussies know how to build bumpers ! |
|
| Author: | Cherrie 274 [ Tue Oct 30, 2012 6:33 pm ] |
| Post subject: | Matrix brush guard on a KK? |
Atthehelm wrote: Wearyman wrote: There is this one too: Big Tube Bar Seems kinda backwards though, a low hanging bumper on top of a bumper? What? if it is the company or a new one like TMJ or TJM they made aluminum bumpers light but strong. It looks big and low but I'm not sure it is. If it is it might be for a roo catcher  .Oh wait TMJ is what I have in my jaw. So it's TJM? |
|
| Author: | KK4x4 [ Wed Oct 31, 2012 1:53 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
That big tube bumper looks like it would just seriously kill the approach angle more then the stock one would |
|
| Author: | tommudd [ Wed Oct 31, 2012 2:12 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
No don't think so if you look at the side profile its higher than the bottom of the flares would be much better than stock bumper PLUS the Aussies make bumpers to last against most anything, not lightweight ones that some US manufacturers come up with. They're made for rocks/animals everything. |
|
| Author: | Sagerist [ Wed Oct 31, 2012 4:34 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
True, but i like the slimmer profile of what Helm and mtnluvr designed. That just seems bulky and like it would absolutely kill what little aerodynamics(  ) the KK has. Plus all that bloody chrome is blinding.
|
|
| Author: | Ted15 [ Wed Oct 31, 2012 6:40 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
KK4x4 wrote: That big tube bumper looks like it would just seriously kill the approach angle more then the stock one would I'd have to agree, it really doesn't matter how well it's made, it just covers the stock bumper adding more bulk in an area that really needs to be trimmed. If you look closely, you'll see that the stock bumper is still on there, look under the turn signal. It looks like it's just a great big chrome cover kinda like what goes over the door handles. Plus it most likely bolts to where the tow hooks go. |
|
| Author: | Ted15 [ Wed Oct 31, 2012 7:15 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
I just sent them an email asking if they made a high clearance winch bumper for the KK. I also asked for a PDF of the directions to see if it might be converted to one. |
|
| Author: | tommudd [ Wed Oct 31, 2012 7:39 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
Chrome  try polished aluminum Plus its made that way for a reason Like I said Aussies know how to build strong bumpers some I've seen so far are like TJ bumpers, worthless |
|
| Author: | Ted15 [ Wed Oct 31, 2012 8:00 pm ] |
| Post subject: | Re: Matrix brush guard on a KK? |
tommudd wrote: Chrome try polished aluminum Plus its made that way for a reason Like I said Aussies know how to build strong bumpers some I've seen so far are like TJ bumpers, worthless I agree, they do make great bumpers I just think this one has an odd look as far as the mounts go. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|