It is currently Fri Sep 21, 2018 8:49 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 46 posts ]  Go to page Previous  1, 2, 3
Author Message
 Post subject: Re: Adding Secondary 2 Micron Fuel Filter
PostPosted: Wed Sep 20, 2017 2:05 pm 
Offline
LOST Addict
User avatar

Joined: Sat Aug 24, 2013 11:36 pm
Posts: 4076
Location: Central GA
taroo wrote:
WWDiesel wrote:
HER_CRD wrote:
Any concern of extra fuel system restriction by adding the secondary filter without having an electric in tank pump?

I would NOT advise adding better filtration without adding an in-tank lift pump! The CP3 struggles at best just to get fuel through the OEM setup using the long vacuum run that it came with from the factory... :roll:
Pulling fuel that far through filters and hoses, and fittings exposes many opportunities for air inleakage and air infusion into the diesel fuel!
Adding a much better primary water separator/filter with better micron numbers and a high efficient secondary fuel filter would add even more restriction without a lift pump... :wink:

Installed my Carter liftpump and now installed the two Donaldson filters. The primary has the new Racor WIF and is a 10 micron filter with water separator. The secondary is the 2 micron filter.

I made the mounting bracket out of 3/16" stock as per your drawing. All went very smoothly.

I could not have done this without the example, drawings, and explanations of WWDiesel..
https://www.dropbox.com/s/l72nui2w54upmh2/File%20Sep%2020%2C%201%2043%2043%20PM.jpeg?dl=0

Looks Good! Your CP3 and injectors will thank you for doing this!
And thanks for the kudo's, but I cannot take all the credit! Ranger1 informed me of this great mod early on right after I purchased my CRD! I liked it so much, I did the same mod to my Dodge Cummins.... :BANANA:
Every diesel CRD should have a dual filter setup for pump and injector protection! :wink:

_________________
05 Jeep Liberty CRD Limited :JEEPIN:
Blk Brush Guard/Hella's/LED's
Ironman Springs/Bilstein's
Yeti Stg4 MaxTune
Weeks ElbowKit/BatteryTray
NO FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pump
2mic.Sec.Fuel Filter
Flowmaster/NOcat
V6 Airbox
GM11 blade fan/NAPA HDclutch
Ironrock Trilink
98 Dodge Cummins, 5"exh. Viair, Huge K&N


Top
 Profile  
 
 Post subject: Re: Adding Secondary 2 Micron Fuel Filter
PostPosted: Wed Aug 01, 2018 5:12 pm 
Offline
LOST Newbie

Joined: Sat Jun 23, 2018 9:53 pm
Posts: 87
Location: WNC
I am going to go with the Donaldson P551313 for a secondary filter.

It has 3 micron um rating after the revised ISO standard, SAE J1858. 99% Efficiency.

They run about $18 or $39 for a pack of 3.

_________________
05 CRD
GDE Eco Full Torque & Towing TCM Tune
Suncoast, TransGo HD2, Sonnax Line Pressure Booster, upgraded Mopar pump/springs
Weeks' Stage 1 & 2
ProVent 200
Samco Hoses
V6 Airbox
Cummins In Tank Pump
2nd Gen Fuel Filter Head,
Donaldson P551313 Secondary Filter
Fumoto valve
OME lift, JBA UCAs
Backbone Winch Mount


Top
 Profile  
 
 Post subject: Re: Adding Secondary 2 Micron Fuel Filter
PostPosted: Wed Aug 01, 2018 9:50 pm 
Offline
LOST Addict
User avatar

Joined: Sat Aug 24, 2013 11:36 pm
Posts: 4076
Location: Central GA
k9adv wrote:
I am going to go with the Donaldson P551313 for a secondary filter.
It has 3 micron um rating after the revised ISO standard, SAE J1858. 99% Efficiency.
They run about $18 or $39 for a pack of 3.

Excellent choice!
You can also use the NAPA 3528 or the Cat 1R-0750 which are both excellent very low micron secondary filters with great ratings.

If you need a custom bracket to mount the secondary filter head on, pm me. I have them in stock available. :D

_________________
05 Jeep Liberty CRD Limited :JEEPIN:
Blk Brush Guard/Hella's/LED's
Ironman Springs/Bilstein's
Yeti Stg4 MaxTune
Weeks ElbowKit/BatteryTray
NO FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pump
2mic.Sec.Fuel Filter
Flowmaster/NOcat
V6 Airbox
GM11 blade fan/NAPA HDclutch
Ironrock Trilink
98 Dodge Cummins, 5"exh. Viair, Huge K&N


Top
 Profile  
 
 Post subject: Re: Adding Secondary 2 Micron Fuel Filter
PostPosted: Wed Aug 15, 2018 11:54 am 
Offline
LOST Newbie

Joined: Sat Jun 23, 2018 9:53 pm
Posts: 87
Location: WNC
Mounted the bracket made by WWDiesel. it is very well made.
Waiting on the Donaldson filter.

Image

Image

Image

_________________
05 CRD
GDE Eco Full Torque & Towing TCM Tune
Suncoast, TransGo HD2, Sonnax Line Pressure Booster, upgraded Mopar pump/springs
Weeks' Stage 1 & 2
ProVent 200
Samco Hoses
V6 Airbox
Cummins In Tank Pump
2nd Gen Fuel Filter Head,
Donaldson P551313 Secondary Filter
Fumoto valve
OME lift, JBA UCAs
Backbone Winch Mount


Top
 Profile  
 
 Post subject: Re: Adding Secondary 2 Micron Fuel Filter
PostPosted: Fri Aug 24, 2018 9:23 pm 
Offline
LOST Newbie

Joined: Sat Jun 23, 2018 9:53 pm
Posts: 87
Location: WNC
Installed and working.

It was mentioned to me the teflon tape was a bad idea and will cause clogging problems. May change it out. Also was told to change out the galvanized elbows to brass, but not given a reason. I searched before buying those (and before using the teflon tape actually) and could not find any cautions against using galvanized with the fuel.

Image

Image

_________________
05 CRD
GDE Eco Full Torque & Towing TCM Tune
Suncoast, TransGo HD2, Sonnax Line Pressure Booster, upgraded Mopar pump/springs
Weeks' Stage 1 & 2
ProVent 200
Samco Hoses
V6 Airbox
Cummins In Tank Pump
2nd Gen Fuel Filter Head,
Donaldson P551313 Secondary Filter
Fumoto valve
OME lift, JBA UCAs
Backbone Winch Mount


Top
 Profile  
 
 Post subject: Re: Adding Secondary 2 Micron Fuel Filter
PostPosted: Fri Aug 24, 2018 10:15 pm 
Offline
LOST Addict
User avatar

Joined: Sat Aug 24, 2013 11:36 pm
Posts: 4076
Location: Central GA
Looks Great! Good job, your CP3 and injectors will thank you for this mod not to mention adding additional longevity to those components. :rockon:

_________________
05 Jeep Liberty CRD Limited :JEEPIN:
Blk Brush Guard/Hella's/LED's
Ironman Springs/Bilstein's
Yeti Stg4 MaxTune
Weeks ElbowKit/BatteryTray
NO FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pump
2mic.Sec.Fuel Filter
Flowmaster/NOcat
V6 Airbox
GM11 blade fan/NAPA HDclutch
Ironrock Trilink
98 Dodge Cummins, 5"exh. Viair, Huge K&N


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 46 posts ]  Go to page Previous  1, 2, 3

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com