It is currently Thu Nov 07, 2024 10:03 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: How to change Injector trim codes for 2004 CRD 2.7l OM612
PostPosted: Tue Sep 17, 2024 12:47 am 
Offline
LOST Newbie

Joined: Mon Sep 16, 2024 10:09 pm
Posts: 2
Hi,
Newby here.
Trying to find out where to add/change the trim code for injectors.
Access to both a DRB III and MPPS-V21.

Had "Black Death" on Injector 1 and have replaced it with a different Bosch injector
Runs OK but there is a noticeable engine beat/shudder when accelerating.
Went through all the DRB III menus (as far as I can tell) but wasn't able to find anything other than "Injector Type" with options 1,2 or 3


ECU Part No: 56044679AA
Extracted ECU information from MPPS
Ecu Selection = Jeep Grand Cherokee 2.7 CRD Bosch EDC15C2
Bosch Hardware Number 0281011409
Bosch Software Number 1037367438


Original Injector:0445110 204
Trim:091104

Replacement injector:0445110 203
Trim:210722

Also interested in a mild firmware mod with EGR/FCV/DTC code delete, to give it a bit more go.
It has the 4-Speed Auto.
Have dumped out the current firmware (approx 512kb)


Any and all help appreciated.


Top
 Profile  
 
 Post subject: Re: How to change Injector trim codes for 2004 CRD 2.7l OM6
PostPosted: Tue Sep 17, 2024 11:00 pm 
Offline
LOST Member

Joined: Thu Dec 13, 2018 10:05 pm
Posts: 148
Location: SoCal
See this video to use the DRB to look/change your injector code for your ECU.

https://m.youtube.com/watch?si=veC4i_Yc ... e=youtu.be

Although you don't really need to do it, the jeep will run just fine without "knowing" what injectors it has installed in what position. The fuel trim levels are super minute and you "may" sense a smoother idle. But hey if you got a DRB then go for it.

**BONUS** Coincidently, that same video also shows how to reprogram an ECU to your jeep too

_________________
05 CRD; Rebuilt top end w/ARP studs, EGR delete, SEGR, 3.7L HD cooling fan, Samco hoses, in tank pump, JBA coil overs & control arms, KK clevis fork, 1/2" cradle drop, 1/4" motor mount lift, WJ rear upper trilink w/WW mount, WJ lower control arms, 4:10 gear, front/rear air lockers, ARB bumper, Rock Lizard sliders/roof rack, Mod T-stat


Top
 Profile  
 
 Post subject: Re: How to change Injector trim codes for 2004 CRD 2.7l OM6
PostPosted: Wed Sep 18, 2024 9:18 am 
Offline
LOST Newbie

Joined: Mon Sep 16, 2024 10:09 pm
Posts: 2
03black wrote:
See this video to use the DRB to look/change your injector code for your ECU.

https://m.youtube.com/watch?si=veC4i_Yc ... e=youtu.be

Although you don't really need to do it, the jeep will run just fine without "knowing" what injectors it has installed in what position. The fuel trim levels are super minute and you "may" sense a smoother idle. But hey if you got a DRB then go for it.

**BONUS** Coincidently, that same video also shows how to reprogram an ECU to your jeep too


Thanks for the link
Will be getting access to the DRB III clone on the weekend.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com