LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

DIY ECU Flash
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=98&t=78418		 Page 79 of 93
Author:  Adriaan Jansen [ Mon Dec 17, 2018 4:55 pm ]
Post subject:  Re: DIY ECU Flash
Yeti deleted my EGR code 403dtc
This guy is the best. Thanks Marco
:D :BANANA: :rockon:
Author:  Yeti [ Mon Dec 17, 2018 5:29 pm ]
Post subject:  Re: DIY ECU Flash
Adriaan Jansen wrote:
Yeti deleted my EGR code 403dtc
This guy is the best. Thanks Marco
:D :BANANA: :rockon:


:wink:

I'm happy that is gone
Author:  michaldenisiuk [ Sat Dec 29, 2018 3:27 pm ]
Post subject:  Re: DIY ECU Flash
hello everyone!!
I love amount of informations on this topic:)
I'm looking for someone who use this USB interface on Chrysler Voyager 2.8CRD 2007? I heard that only DRB3 can comunicate with this italy VM engine
I want to remove EGR and USR system, turn of the check engine light and delete all DTC that was stored on my ECU

thank You for any help :)
Author:  Yeti [ Sat Dec 29, 2018 3:49 pm ]
Post subject:  Re: DIY ECU Flash
michaldenisiuk wrote:
hello everyone!!
I love amount of informations on this topic:)
I'm looking for someone who use this USB interface on Chrysler Voyager 2.8CRD 2007? I heard that only DRB3 can comunicate with this italy VM engine
I want to remove EGR and USR system, turn of the check engine light and delete all DTC that was stored on my ECU

thank You for any help :)


163 hp edc16cp31, mounted on WK ,KK ,XK and JK normally I use kess v2 tool but I know someone with mpps v18 have write this ecu , sincerelly I never tried with mpps v18

if you need support on this ecu for tuning etcc I can do all you need

Marco
Author:  michaldenisiuk [ Sat Dec 29, 2018 5:14 pm ]
Post subject:  Re: DIY ECU Flash
Yeti, it would be awsome but my engine is 150hp :)
Author:  CaptainDean [ Sat Dec 29, 2018 7:58 pm ]
Post subject:  Re: DIY ECU Flash
Squeeto,

Regarding the originating post of this thread, here are the files from the MPPS V13.02 CD that comes with the MPPS V13 cord and smart connector. They are stored in a folder in Dropbox.com, and here is a link to that folder...
https://www.dropbox.com/sh/j2hj5z74bqgz ... Rjn2a?dl=0

It would be great if you would edit this link into your originating post for this thread. Anyone that cannot find their CD or it won't play, they will be able to use it.

Dean.
Author:  Yeti [ Sun Dec 30, 2018 8:15 am ]
Post subject:  Re: DIY ECU Flash
michaldenisiuk wrote:
Yeti, it would be awsome but my engine is 150hp :)


150hp is like the old KJ edc15c2 same as WJ and people do this ecu with mpps v13 ;-)
Author:  michaldenisiuk [ Sun Dec 30, 2018 10:58 am ]
Post subject:  Re: DIY ECU Flash
so I just order mpps v13, if upload binary from my ECU could you help me turned off EGR and air flow valve?
I just wondering is the MAF sensor is needed on my engine? only with MAP sensor ECU can handle without any issue? what do you thing? turned off the MAF or dont touch ?
please excuse for my english :)
Author:  Yeti [ Tue Jan 01, 2019 4:54 pm ]
Post subject:  Re: DIY ECU Flash
are you sure you have the maf sensor ? By the Way I need to see the ecu file for give you a stright answer , once I have see the management I can say if is like the old 150 hp KJ or if is like the WJ
Author:  michaldenisiuk [ Wed Jan 02, 2019 5:19 am ]
Post subject:  Re: DIY ECU Flash
yes, Im sure, few days ago clean that sensor and MAP,
when disconnect MAF car drive terrible so maybe its ok.
I will upload binary if get the OBD interface, so only EGR need to be disabled. thank you :)
Author:  darinb [ Thu Jan 03, 2019 12:43 pm ]
Post subject:  DIY ECU Flash
I had to replace my ECU at a local shop about 100,000 miles ago and the cruise control hasn’t worked since that time. I have the MPPS cable and have been flashing the ECU some. Is there a way to enable cruise control via MPPS? The local shop had the dealer program the ECU when it was switched.


Sent from my iPhone using Tapatalk
Author:  Yeti [ Thu Jan 03, 2019 1:35 pm ]
Post subject:  Re: DIY ECU Flash
for what I know the dealer need to activate with the diagnostic tool , ps what is the cost you have payed for the new ecu ?
Author:  darinb [ Thu Jan 03, 2019 6:19 pm ]
Post subject:  Re: DIY ECU Flash
Ok thanks for letting me know. I think the guy charged me around $800 for the new ECU and programming


Sent from my iPhone using Tapatalk
Author:  Dez [ Thu Jan 03, 2019 11:21 pm ]
Post subject:  Re: DIY ECU Flash
Does anyone have a 808 tune file (STOCK OR Modified) with 7 VOLT? I'm tired of Bosch 5v glow plugs and 5 volt programming!
Author:  Yeti [ Sat Jan 05, 2019 7:22 am ]
Post subject:  Re: DIY ECU Flash
darinb wrote:
Ok thanks for letting me know. I think the guy charged me around $800 for the new ECU and programming


Sent from my iPhone using Tapatalk


probably cost less to ship in Italy an used ecu to me :shock: :shock: :shock: :shock: :shock: :shock:
Author:  Yeti [ Sat Jan 05, 2019 7:24 am ]
Post subject:  Re: DIY ECU Flash
Dez wrote:
Does anyone have a 808 tune file (STOCK OR Modified) with 7 VOLT? I'm tired of Bosch 5v glow plugs and 5 volt programming!



post here your original and I compare it
Author:  michaldenisiuk [ Sat Jan 05, 2019 1:18 pm ]
Post subject:  Re: DIY ECU Flash
YETI,

yesterday MPPS V13.02 arrived, thats what I get from my ECU https://drive.google.com/open?id=1tmtXV ... 0a0APmp3XL
always 402 EGR issue occure

Chrysler Voyager 2.8CRD 150HP 2007
BOSCH EDC15C2
Author:  Yeti [ Sat Jan 05, 2019 5:31 pm ]
Post subject:  Re: DIY ECU Flash
downloaded , I take a look tomorrow
Author:  michaldenisiuk [ Sat Jan 05, 2019 5:56 pm ]
Post subject:  Re: DIY ECU Flash
thank You :)
Author:  Yeti [ Mon Jan 07, 2019 3:43 am ]
Post subject:  Re: DIY ECU Flash
you have private message , p0402 is for stuck open egr you need to block the valve with a plate
Page 79 of 93 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/