LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
Installed Yeti DTC delete but still getting egr code http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=98&t=90965 |
Page 1 of 2 |
Author: | norm1001 [ Tue Feb 11, 2020 7:12 pm ] |
Post subject: | Installed Yeti DTC delete but still getting egr code |
I used the Yeti tune for the 16 that say code delete, i completely remove the EGR cooler and valve and removed the butterfly from the throttle body, is there something i am missing, |
Author: | Mountainman [ Tue Feb 11, 2020 9:10 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
What's the full name of the tune you used? |
Author: | norm1001 [ Tue Feb 11, 2020 9:38 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Yeti's 808 EGR/FCV delete + Mild tune (vers 1.02) - 450Nm, link- https://www.dropbox.com/s/bp92djgcim1z9 ... -450Nm.bin -description- viewtopic.php?f=98&t=78418&start=58 I have sone am 05 and didnt have a problem, i didnt remove the coole and egr valve on it tho |
Author: | Mountainman [ Wed Feb 12, 2020 11:51 am ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Ok, tune looks good. what fault codes are you getting? The fault codes will still show up when you pull the codes, however, they won't trigger the check engine light after the tune. So, I'm guessing that it's a different fault that's causing your problem. |
Author: | norm1001 [ Wed Feb 12, 2020 1:39 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
I have P1267, P0102, U0121, P0403, thanks |
Author: | WWDiesel [ Wed Feb 12, 2020 3:44 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
What was the file number for your original .bin file? Based on those codes, you may have flashed using an incorrect file for your build. |
Author: | Mountainman [ Wed Feb 12, 2020 4:16 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
norm1001 wrote: I have P1267, P0102, U0121, P0403, thanks P1267 is a bad glow plug, probably #4, or #1 if the wire is backwards. U0121 is ABS related, so like WW said, give us your file number as that's a strange one. But, you can ignore the EGR and FCV codes. I always leave the fcv and egr disconnected after the tune... |
Author: | Mountainman [ Wed Feb 12, 2020 4:21 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
You may also have a bad (wire or sensor) or unplugged mass air flow sensor (maf). I'm assuming that the jeep starts and runs? |
Author: | norm1001 [ Wed Feb 12, 2020 8:59 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Thanks i checked all connections and they are good no loose pins or bent pins, i did one other jeep 2005 an it also got the U0121 code, so i am thinking I'm either down loading the wrong files or they need tohave the serial number enters in the program, here is the original for the 2006 jeep and the one i put in it, i even reloaded it to make sure there wasn't a glitch. i dont know how to get a bin file to the forum, but it was a 16 file |
Author: | Mountainman [ Thu Feb 13, 2020 1:11 am ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Open the file in *Wordpad and look for the number that is similar to 1037380808. It will have 10 digits. Does the jeep start? |
Author: | Mountainman [ Thu Feb 13, 2020 12:11 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Oops, I meant Wordpad! |
Author: | norm1001 [ Fri Feb 14, 2020 3:34 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
I appreciate the help, sorry for the time to reply, i have been dealing with the nasty flu that is going around this year. the original file number is 1037380808p53363k0. thanks, Norm |
Author: | norm1001 [ Fri Feb 14, 2020 4:10 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
the number you posted is the tune number, thanks |
Author: | Mountainman [ Sat Feb 15, 2020 1:21 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Ok, as long as the jeep actually runs, then your tune is fine. You just need to fix the glowplug and ABS issue. In other words: You will always see the egr code when you pull the codes, but it won't cause a check engine light. |
Author: | norm1001 [ Sat Feb 15, 2020 2:53 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
It didn't have the can bus issue with the abs till i tuned it, same with the other jeep i have been working on, i checked everything i the other jeep and found no concerns, is it possible after the tune the abs doesn't recognize the ECM, i don't think it coincidence that both have the same can bus issues. thanks, Norm |
Author: | Mountainman [ Sat Feb 15, 2020 4:08 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
norm1001 wrote: It didn't have the can bus issue with the abs till i tuned it, same with the other jeep i have been working on, i checked everything i the other jeep and found no concerns, is it possible after the tune the abs doesn't recognize the ECM, i don't think it coincidence that both have the same can bus issues. thanks, Norm Where are you located? Or is this a US jeep? I would first try loading a different 808 tune. Send Yeti a PM if there isn't another 808 in the DIY tune thread. Or start a new thread in the CRD section and ask for a different 808 tune. I'm guessing you are dealing with a non US jeeps. For clarification, do the jeeps start, run, opperate??? |
Author: | WWDiesel [ Sat Feb 15, 2020 4:12 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Don't believe adding a tune on the ECM has any bearing on the ABS Module. They are stand alone entities. |
Author: | norm1001 [ Sat Feb 15, 2020 4:36 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
all the modules are on the bus DATA line and if they see one that is different or doesn't communicate like it suppose to it set a bus code, which i am getting, they cant be separate if the ECM is getting the code. there is a sequence that they have to start up and i think the sequence has been changed with the tune. it does start and runs good but the guy wants the check engine light to be off. |
Author: | norm1001 [ Sat Feb 15, 2020 4:38 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
It is a US Jeep in Washington state. |
Author: | norm1001 [ Sat Feb 15, 2020 4:39 pm ] |
Post subject: | Re: Installed Yeti DTC delete but still getting egr code |
Mountainman i appeciate your help, ive been doing programming for 30 years and this is baffling me. |
Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |