Anybody get any creaking noise when going over a curb like at the end of a driveway? Mine has a loud creak just when I go over the end of my driveway maybe I need new shocks up front. Any suggestions?

When the temp is below about 50 my front swaybar bushings creak over speedbumps and such. Pretty common in these vehicles.

_________________
05CRD: GDE Hot ECU & TCM tunes, Provent, Cat filter, Facet lift pump, TransGo kit, Florida TC, Samcos, stainless brake lines, HDS thermostat, Renegade light bar,
RL super sliders, Bilstein adjustables, Al's Gen 4.5 Arms, 235/85-16 Duratracs, DTT rear, Elocker front, EVIC+TPMS, Turbo timer, McNally pillar gauges, Weeks Stage II kit.

Can we put some lubricant on them to quiet them down a bit?

Some people remove the bar to put silicone spray on the bushings.

Here's an idea I may copy.

http://www.lostjeeps.com/forum/phpBB3/vie ... hp?t=12494

_________________
05CRD: GDE Hot ECU & TCM tunes, Provent, Cat filter, Facet lift pump, TransGo kit, Florida TC, Samcos, stainless brake lines, HDS thermostat, Renegade light bar,
RL super sliders, Bilstein adjustables, Al's Gen 4.5 Arms, 235/85-16 Duratracs, DTT rear, Elocker front, EVIC+TPMS, Turbo timer, McNally pillar gauges, Weeks Stage II kit.

i've tried that and it doesn't seem to work

_________________
Trevor

'05 Limited CRD Inferno Red Pearl Coat
Home made provent installed @ 35443, SEGR installed @ 35466, Fumoto valve @ 37500, trans and transfer case skid, In tank pump installed @ 43500, Suncoast TC & Transgo Shift Kit @ 44730, EGT, Boost, Trans temp gauges, Samco hoses, Rebuilt Trans w/ HD454RFE kit @ 56K, Inmotion Stage 2 @ 56K

Tried the spray or the zerks? Something else may be squeaking, there are a lot of bushings up front.

Anyway, suspension related questions should go in another forum.

_________________
05CRD: GDE Hot ECU & TCM tunes, Provent, Cat filter, Facet lift pump, TransGo kit, Florida TC, Samcos, stainless brake lines, HDS thermostat, Renegade light bar,
RL super sliders, Bilstein adjustables, Al's Gen 4.5 Arms, 235/85-16 Duratracs, DTT rear, Elocker front, EVIC+TPMS, Turbo timer, McNally pillar gauges, Weeks Stage II kit.

I hope he is not shooting wheels grease into those bushings.

Also Silicon spray does not work, you have to use silicone paste. They have to be takens off, cleaned and re-installed with the new silicon grease.

_________________
No longer a CRD or Jeep owner. Selling everything I have, needs to go as I need the room for a project.

Sorry for hot to say which one...

Took the bushings off cleaned them.. Drilled and tapped for the zerks... Spread synthetic grease in there... Worked for a day... Squirted some more in the zerks... Worked for two days...


My next try is going to be the nylon or something like that bushings with the zirks built in... Saw em for like 28 bucks a piece.

_________________
Trevor

'05 Limited CRD Inferno Red Pearl Coat
Home made provent installed @ 35443, SEGR installed @ 35466, Fumoto valve @ 37500, trans and transfer case skid, In tank pump installed @ 43500, Suncoast TC & Transgo Shift Kit @ 44730, EGT, Boost, Trans temp gauges, Samco hoses, Rebuilt Trans w/ HD454RFE kit @ 56K, Inmotion Stage 2 @ 56K