SEGR/ORM Kit Builder's Thread

UFO · **Posted:** Wed Nov 05, 2008 7:14 pm

Tinman wrote:

I finally got around to installing the SEGR. After install, I got 2 codes. I don't recall the numbers, but one was short circuit for EGR circuit and other was short circuit of the MAF circuit. I unplugged it, put in the jumpers and haven't had a chance to look at it again. I figure I must have the input/output to the box backwards. Any thoughts??

If you can post the exact codes, that would be useful. But offhand (did I build your box?) it sounds like you may have wired it into your harness incorrectly. There is no way to wire the EGR short - it is permanently disconnected. And the MAF may be reversed, that is a common wiring error.

UFO · **Posted:** Wed Nov 05, 2008 7:16 pm

pablo0423 wrote:

Doew anyone have a good set of instructions with photos for the install of the completed (soldered) SEGR? Being a coward, I want to follow a visual path!
thanks
pablo

I wrote a set specifically for installing boxes and harnesses that I built. PM me with your email address and I can sent them to you. They are a bit light on pictures, but I think they may be adequate.

Tinman · **Joined:** Mon Apr 10, 2006 10:45 am **Posts:** 308

This is weird. I didn't write down the codes the first time, but I remember them by description. They where P0490 and P0103. So I hooked it up yesterday to comfirm the codes. Got 403 and 1140. This morning, I tried again and low and behold it seemed to work. No codes. The large resistor got warm after a few minutes of running. I did serveral cranks and re-checked codes. All was good. So I unplugged it to put the cover on the box and a few other things. Plugged it back in and got the 490 code again and it won't go away. Also, when I start it, it throws 102 (MAF is plgged in). I also briefly had 1140 again, but it when away. Any hwlp would be greatly appreciated.

05infernoCRDL · **Posted:** Fri Nov 14, 2008 2:26 pm

tin man,

i have found that if you unplug and replug the box in too soon after shutdown,
you get codes (found this out by switching known good boxes)... run it plugged
in for a few days and note any changes

hope that is what it is

*edit* after reading through more of the thread..
make sure you didn't get your MAF wires switched... they are opposite the others
I.E. say one end is negative (3,6,9) and the other is positive (2.5,8)

6,9 come from the ECU, 5,8 go to the component
the MAF is opposite... 3 from MAF, 2 to ECU
(not saying that those numbers are right just an illistration)

I mixed those up and got MAF codes

Tinman · **Joined:** Mon Apr 10, 2006 10:45 am **Posts:** 308

Getting the wires backwards was my first thought. But if that where the case how could it run any length of time without setting codes as it did earlier today?

05infernoCRDL · **Posted:** Sun Nov 16, 2008 2:17 am

Codes aren't thrown immediately... I have driven for 30 min before a code WAs thrown... Depends on the car I guess

moto-scoot · **Posted:** Sun Nov 16, 2008 3:20 am

Just a note to those of you running ORM and imune to CEL light.
Scanned mine a while back and found code for #3 glow plug.
Pulled & replaced #3 glow plug. It was cracked the entire length of ceramic!!
:oops:

If this had broken off it would have been time to pull head!!!!!!!!

Tinman · **Joined:** Mon Apr 10, 2006 10:45 am **Posts:** 308

The codes could be delayed. Still kinda weird how it's different codes at different times. Could I just plug it up and drive it a little while and see? Wouldn't it be just like the ORM? Can those codes harm the SEGR?

Squeeto · **Posted:** Tue Nov 18, 2008 4:42 pm

Hi,
I added a simple SEGR tester circuit here:

http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?p=393224#393224

05infernoCRDL · **Posted:** Mon Jan 26, 2009 6:12 pm

revival and questions.....

i just installed an SEGR on another forum member's truck... the fan now runs when the key is turned and he has a mil... OBD2 readers say the MIL should be off....

the only difference in the vehickes are his is an 06 mine is an 05... i ran the box in my truck no problem... he has some..

and thoughts?

UFO · **Posted:** Mon Jan 26, 2009 6:57 pm

05infernoCRDL wrote:

revival and questions.....

i just installed an SEGR on another forum member's truck... the fan now runs when the key is turned and he has a mil... OBD2 readers say the MIL should be off....

the only difference in the vehickes are his is an 06 mine is an 05... i ran the box in my truck no problem... he has some..

and thoughts?

This sounds similar to one of the first installers of this box. I believe there is a wiring error in the harness.

taroo · **Joined:** Sun Apr 27, 2008 2:14 pm **Posts:** 292

Loco, Tim, UFO, GMCTD, et al

I finally built the circuit board, wired it up, installed it and it worked the first time. I did a lot of reading on this board and assimilated all the tips and lessons-learned. So, given that the EGR lead is open (pin 5 is open) then I suppse it is working as advertised. No CEL at anytime. The box is getting a little warm where the power resistor is located. So, thanks to all of you as the idea of an EGR on the CRD is a bad one. Congress and EPA!!!!

Now, I will start working on my Provent. Any tips on how to improve the intake airflow as well would be appreciated. I know I need to do the Magnaflow as also.

Thanks to all here on inventing and proliferating the SEGR.

moto-scoot · **Posted:** Tue Mar 17, 2009 11:57 am

Installed my box ,have code P0100

Maf voltage low.
while running have 12 volt at white wire
0 VOLTS AT WHITE/RED WIRE
SCAN TOOL SAYS MAF 0.00 volts

UFO · **Posted:** Tue Mar 17, 2009 1:23 pm

moto-scoot wrote:

Installed my box ,have code P0100

Maf voltage low.
while running have 12 volt at white wire
0 VOLTS AT WHITE/RED WIRE
SCAN TOOL SAYS MAF 0.00 volts

Is pin 1 of your box shorted to ground or miswired? Did you swap pin 1 with pin 2, or wire pin 1 to the ECU instead of to the MAF? Is your MAF plugged in?

Lots of things to check. You could email or post close up pictures of both sides of your PCB, and we could tell if you assembled the board correctly.

LocoCRD · **Posted:** Tue Mar 17, 2009 1:57 pm

moto-scoot wrote:

Installed my box ,have code P0100

Maf voltage low.
while running have 12 volt at white wire
0 VOLTS AT WHITE/RED WIRE
SCAN TOOL SAYS MAF 0.00 volts

Yep sounds like you swapped SEGR wire #1 and SEGR wire #2 somewhere and maybe something else too. I would double check the connections where you spliced into the jeep harness to make sure everything is going to the right wire. It is a pretty common error to accidently swap either 1 & 2, 4 & 5, and/or 7 & 8.

moto-scoot · **Posted:** Tue Mar 17, 2009 2:02 pm

no codes wih bypass plug
maf volts 1.76etc
pin 2 wired to ecm c1-85
where is pin 1wire connected to board?
mines at Rpwr1 bottom left of board

LocoCRD · **Posted:** Tue Mar 17, 2009 2:03 pm

moto-scoot wrote:

no codes wih bypass plug
maf volts 1.76etc
pin 2 wired to ecm c1-85
where is pin 1wire connected to board?
mines at Rpwr1 bottom left of board

Check your PM and give me a call.

moto-scoot · **Posted:** Tue Mar 17, 2009 2:05 pm

will do after this alignment

LocoCRD · **Posted:** Tue Mar 17, 2009 2:09 pm

pin 1 goes to "1" on the PCB
pin 2 goes to "2" on the PCB...etc

wire 1 goes to pin 1 on connector
wire 2 goes to pin 2 on connector...etc

Rpwr1 and Rpwr2 each connect to opposite ends of the power resistor

Heres where the wires should be on the connectors:

UFO · **Posted:** Tue Mar 17, 2009 2:23 pm

moto-scoot wrote:

no codes wih bypass plug
maf volts 1.76etc
pin 2 wired to ecm c1-85
where is pin 1wire connected to board?
mines at Rpwr1 bottom left of board

Did you let any smoke out? Check your parts and traces if you smelled anything burning.

SEGR/ORM Kit Builder's Thread

Who is online