It is currently Wed Oct 28, 2026 1:45 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 43 posts ]  Go to page 1, 2, 3  Next
Author Message
 Post subject: ride hieght?
PostPosted: Thu Jul 10, 2008 5:07 pm 
Offline
This member has been Banned

Joined: Sat May 03, 2008 10:48 am
Posts: 512
does anyone else that has or had the RUSTY'S coil lift or spacer lift, and an '02 KJ, sit a lil higher then other years? on the front, i am sitting right around 37" to the bottom of the front flare dead center with the hub. and 38" on the back. and that with my TOYO'S on that are 245-70-16, its even higher with the TSL's on. anyone else experience this. like i said beofre, i will have pics up later, i dont have time right now to load them and then host them and then post them on here so i will do that when i get home. by for now


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 5:31 pm 
Offline
LOST Addict
User avatar

Joined: Tue Sep 05, 2006 10:38 pm
Posts: 5334
Location: Biggest Little City
Am I reading this wrong? Do you mean 27 and 28 and not 37 and 38? That would give you over 10" from my Frankenlift instead of around 4. Are you measuring starting from the ground or in the dead center of the hub? Measure from the hub center to the bottom of the fenders and see what it is.

_________________
My Jeep Build ----> Big Black
Image


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 5:32 pm 
Offline
LOST Member
User avatar

Joined: Tue Dec 25, 2007 2:58 pm
Posts: 432
Location: Loveland, OH.
2002 and very early 2003 KJ's sat about 3/4" higher till Chrysler lowered them to where they sit in later '03 and up due to roll-over concerns with a certain car review mishap. Thats why they refer to them as "pre-lowered". So yes, your does sit a little higher :) . Well, now that I re-read...is this what you are asking?

Another question...where do you keep the spare??

_________________
'74 CJ5
304/T15


Last edited by modular on Thu Jul 10, 2008 5:36 pm, edited 2 times in total.

Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 5:32 pm 
Offline
LOST Addict
User avatar

Joined: Mon Jan 29, 2007 12:54 am
Posts: 3865
Location: Draper, UT
Mine is right at 21" (measured from the hub) with an ARB bumper with winch and very heavy diesel engine pressing down on my FLII 2.5" lift.
Maybe something is horribly wrong.....how are your CV angles? That would be a good pic to see :D

_________________
2006 CRD http://www.UtahPowderCoatings.com/ http://www.gorecon.com/ I'm kind of a big deal.
RL rear bumper, ARB front bumper, Mile Marker winch, Power Tank, Skids by Mopar & Skid Row, RL Super Skink Sliders, 235/85R16 MTR, Air Flow Snorkel, DTT, 4.10 gears, Frankenlift II, Katskin leather, JL Audio stereo, Rosen video.


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 6:15 pm 
Offline
Lifetime Member
Lifetime Member

Joined: Sun Nov 04, 2007 3:02 am
Posts: 2053
Location: Michigan City, IN
I have 21 ¼" c/l hub to bottom of flare on front and 20" on the rear with my daystar. Wish I would have known how to measure right before I put the lift on.

_________________
Blood Clot Red 03 Punisher Edition
245/75-16 Duratracs, Soft 8's, Ironman/clevis Lift, Monroe Sensa-trac rear shocks, JBA 3.5, GTP Hood Louvers, Roof Basket & Light bar, Mudd's Garage Rear Bumper
custom made items: cross rails, grill inserts, cargo shelf, lightbar, pin stripping & rock rails.
L.O.S.T. #DW090501


Last edited by 501 on Thu Jul 10, 2008 10:47 pm, edited 1 time in total.

Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 6:48 pm 
Offline
LOST Member

Joined: Fri Nov 02, 2007 4:17 pm
Posts: 250
If you're using a coil lift your year no longer affects lift height, spacers do however.

_________________
Patriot Blue 04 KJ
OME HD lift w/ 1/8" Clevis lift
LT 245/75/16 Revo's
Husky liners
Aeroturbine 2525
Amsoil


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 7:10 pm 
Offline
Lifetime Member
Lifetime Member
User avatar

Joined: Sat Jul 01, 2006 9:19 pm
Posts: 4129
Location: Saint Augustine, FL
22" front and 20.5" rear.

Terry

_________________
Image2011 Ford F-150 XLT 4X4


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 7:33 pm 
Offline
LOST Member
User avatar

Joined: Sat Mar 04, 2006 10:02 pm
Posts: 166
Location: Columbia, CT
20" front & rear (no clevis)

_________________
2002 Salsa Liberty
Rusty's 2.5 spring lift
Rusty's RockRails and Diff Guards
Skid Row belly skidplate
235/85/R16 (32") Maxxis BigHorns
ARB rear locker
Detours BackBone Front Recovery Point and Winch Mount
Superwinch EP9000


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 7:46 pm 
Offline
LOST Addict
User avatar

Joined: Tue Sep 05, 2006 10:38 pm
Posts: 5334
Location: Biggest Little City
23" Front
22.75" Rear
Frankenlift II (extra set of rear isolators, no clevis)

_________________
My Jeep Build ----> Big Black
Image


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 9:37 pm 
Offline
Moderator / Lifetime Member
Moderator / Lifetime Member

Joined: Thu Jul 07, 2005 5:49 pm
Posts: 27226
Location: NOW Southeastern Ohio/ Tanzania
I think you either need to remeasure or really look to make sure you have it put together correctly. I mean Troy is at 37 5/8 with 265-75s and everything he has done!

Pictures of the CVs at that heighth!

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 9:45 pm 
Offline
Lifetime Member
Lifetime Member

Joined: Sat Apr 01, 2006 9:38 pm
Posts: 12988
Location: Colorado Springs
tommudd wrote:
I think you either need to remeasure or really look to make sure you have it put together correctly. I mean Troy is at 37 5/8 with 265-75s and everything he has done!

Well I'm sitting at about 39" in the front right now but I'm kinda missing the front diff and CV's(along with all my skids) so about 350lbs or so of lost weight.


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 10:18 pm 
Offline
LOST Addict

Joined: Mon Sep 04, 2006 10:12 pm
Posts: 2476
Location: Jamestown PA
i parked mine on a flat, level spot (my garage) and took some measurements

Front
Ground to flare = 38
Hub to flare = 23in
Back
Ground to flare = 37
Hub to flare = 22 in

i have a frankenlift.. extra rear iso. and 265/75/16's that are about half worn out.

_________________
2006 Renegade. Completely stock.


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 10:31 pm 
Offline
LOST Addict
User avatar

Joined: Thu Nov 16, 2006 6:10 pm
Posts: 1322
Location: Richmond, VA
newer and older style kj's have different fender flares (or is it just the turn signal placement)....not sure if that will make a difference in measurements.....so just keep that in mind with all the replys

_________________
L.O.S.T. #225019
2003 Sport 4x4
Patriot Blue w/ trail rash
Flex-Zilla 4" Lift
TrailRash hi-lift mounts
Other stuff you wish you had :-)


Top
 Profile  
 
 Post subject:
PostPosted: Thu Jul 10, 2008 11:15 pm 
Offline
Moderator / Lifetime Member
Moderator / Lifetime Member

Joined: Thu Jul 07, 2005 5:49 pm
Posts: 27226
Location: NOW Southeastern Ohio/ Tanzania
2006 KJ wrote:
i parked mine on a flat, level spot (my garage) and took some measurements

Front
Ground to flare = 38
Hub to flare = 23in
Back
Ground to flare = 37
Hub to flare = 22 in

i have a frankenlift.. extra rear iso. and 265/75/16's that are about half worn out.


Same as you on the hub to flare, I just don't have those TALL tires mines the same front and rear though, have to get those 4.10s in before I get taller though!

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 11, 2008 7:47 am 
Offline
LOST Addict

Joined: Mon Sep 04, 2006 10:12 pm
Posts: 2476
Location: Jamestown PA
tommudd wrote:
2006 KJ wrote:
i parked mine on a flat, level spot (my garage) and took some measurements

Front
Ground to flare = 38
Hub to flare = 23in
Back
Ground to flare = 37
Hub to flare = 22 in

i have a frankenlift.. extra rear iso. and 265/75/16's that are about half worn out.


Same as you on the hub to flare, I just don't have those TALL tires mines the same front and rear though, have to get those 4.10s in before I get taller though!


naaaa it'll be fine everyones doin' it! (nothing like peer pressure) :twisted: did you have to change your front springs to maintain that front height with the ARB up there?

_________________
2006 Renegade. Completely stock.


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 11, 2008 8:34 am 
Offline
LOST Addict
User avatar

Joined: Thu Jul 19, 2007 3:52 pm
Posts: 1184
Location: Atlanta, GA
20.5" Front and Rear (with clevis and 1 extra isolator).

_________________
Colin
LOST#85291
"Blue Bunny"
04 KJ Sport 3.7L AT 4x4
Steel IFS/DL&DTT/4.10s/Tow Pkg/Mopar-Rusty's-Skid Row skids&sliders/OME struts&springs/Rancho shocks/Terraflex bumpstops/Landy FRH/Gen Steel/Grabber AT2s/Spidertrax/Rockcrusher/Hella/Smittybilt XRC8/Bulldog wiring/NAPA brakes/JBA UCAs&spacers/Deka Intimidator


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 11, 2008 9:58 am 
Offline
Moderator / Lifetime Member
Moderator / Lifetime Member

Joined: Thu Jul 07, 2005 5:49 pm
Posts: 27226
Location: NOW Southeastern Ohio/ Tanzania
2006 KJ wrote:
tommudd wrote:
2006 KJ wrote:
i parked mine on a flat, level spot (my garage) and took some measurements

Front
Ground to flare = 38
Hub to flare = 23in
Back
Ground to flare = 37
Hub to flare = 22 in

i have a frankenlift.. extra rear iso. and 265/75/16's that are about half worn out.


Same as you on the hub to flare, I just don't have those TALL tires mines the same front and rear though, have to get those 4.10s in before I get taller though!


naaaa it'll be fine everyones doin' it! (nothing like peer pressure) :twisted: did you have to change your front springs to maintain that front height with the ARB up there?


I put the OME Heavy Dutys and the ARB on over 70,000 miles ago , did them with in 10 days of one another so didn't/haven't changed from then. As far as going to 265s not until the 4.10s, I tow a trailer way to much to be dogged down when I am in the hills of Southeastern Ohio :wink:

Tom

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 11, 2008 10:28 am 
Offline
LOST Addict
User avatar

Joined: Mon Jan 29, 2007 12:54 am
Posts: 3865
Location: Draper, UT
10-4 on that Tom. I still had stock gears (and 32" tires) back in February when I was towing all my stuff from UT to FL (about 6K pounds). When I was crossing the UT/WY border on I 80 throught the Uinta Mntns, there were gusting head winds and it was all I could do to maintain 30 mph (pedal floored). As snow started falling and visibility dropped, it was a very hazardous condition. Especially when you consider the peeps from WY drive along I80 like God is their co-pilot! :D

_________________
2006 CRD http://www.UtahPowderCoatings.com/ http://www.gorecon.com/ I'm kind of a big deal.
RL rear bumper, ARB front bumper, Mile Marker winch, Power Tank, Skids by Mopar & Skid Row, RL Super Skink Sliders, 235/85R16 MTR, Air Flow Snorkel, DTT, 4.10 gears, Frankenlift II, Katskin leather, JL Audio stereo, Rosen video.


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 11, 2008 11:47 am 
Offline
LOST Addict

Joined: Mon Sep 04, 2006 10:12 pm
Posts: 2476
Location: Jamestown PA
valid point. i dont tow with my KJ (no hitch). soo i guess i'll let it slide this time. but once the 4.10's are in there i expect to see 33's!

_________________
2006 Renegade. Completely stock.


Top
 Profile  
 
 Post subject:
PostPosted: Fri Jul 11, 2008 12:11 pm 
Offline
Moderator / Lifetime Member
Moderator / Lifetime Member

Joined: Thu Jul 07, 2005 5:49 pm
Posts: 27226
Location: NOW Southeastern Ohio/ Tanzania
2006 KJ wrote:
valid point. i dont tow with my KJ (no hitch). soo i guess i'll let it slide this time. but once the 4.10's are in there i expect to see 33's!


Oh you will, have them picked out already :twisted:

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 43 posts ]  Go to page 1, 2, 3  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 4 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com