What trailer wiring harness do I need can I get for the liberty? I have a 2004. I don’t plan on pulling any major but I’d like to have the option for something that can use trailer brakes. Do I need a 4-pin or a 7 pin? Can I set it up for both? If possible I’d like a plug in version but I can also splice wires myself so long as I can clearly figure out what’s what.

I’d also like to have it permanently mounted to the hitch and not some wires that are tucked inside the Jeep and then just pulled out when I need it.

_________________
'04 Liberty Limited - 245/70/16 Firestone Destination AT's, Mopar tow hooks, Draw-Tite Class IV hitch, Skid Row Engine & Transmission Skids, Mopar T-Case & Gas Tank Skids, Extended Breather Tubes, Red Top Optima, Sylvania Silver Star head lights, Hella 500FF bumper mounted driving lights

most small trailers take the 4 pin flat plug, and go to etrailers, good prices and a good product also it just plugs into the KJ rear wiring no cutting of wires

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

so can the 4-pin set up control trailer brakes? Or do I need a 7-pin to do that?

_________________
'04 Liberty Limited - 245/70/16 Firestone Destination AT's, Mopar tow hooks, Draw-Tite Class IV hitch, Skid Row Engine & Transmission Skids, Mopar T-Case & Gas Tank Skids, Extended Breather Tubes, Red Top Optima, Sylvania Silver Star head lights, Hella 500FF bumper mounted driving lights

need 7 to do that plus the brake controller etc

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

I bought this exact harness from this ebay vendor and it was really easy to install and works great. It was the cheapest I could find. It came in a Reece Towpower container, I bet most 4 pin plug-and-play setups are made in the same place.

http://cgi.ebay.com/ebaymotors/Trailer- ... enameZWDVW

try this all in one. http://www.etrailer.com/p-118382.htm

_________________
____________________
'07 Jeep Liberty Sport
Frankenlift II Premium
Mopar Armor & Tow Hooks
Amsoil
Reese Hitch
Masterbuilt aluminum carrier

i have this one and it works great but i got mine from summit racing its a little bit more there but no shipping

_________________
1980 Jeep CJ7 Buggy
SOA, D44/ FF14B, SBC 350, SM465, NP205, 108" WB, 37" MTs

http://www.dpgoffroad.com/
http://www.ucora.org/
http://www.christianoffroad.com/
http://jeepinbyal.com/

Get a 7 pin harness.

You can always install a 7 pin to 4 pin converter for any trailer, but not the other way around.

_________________
http://www.Colorado4Wheel.com
"Its not about what you can DO with your Jeep, its about where you can GO with your Jeep."
Knowledgeable - But Caustic

This was a good post
http://www.jeepkj.com/forums/viewtopic.php?t=1691

_________________
2005 CRD
stuff
Skeptic quod gratis asseritur, gratis negatur