One is for a ground to light up the little light in the switch..
Make sure you have it wired right.. Dont want to make alittle fire when you turn the switch on..
The switch that came with my hellas was labeled which was ground and everything.
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Hellas mounted but... http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=15926 |
Page 1 of 1 |
| Author: | garyg [ Tue Dec 26, 2006 3:19 pm ] |
| Post subject: | Hellas mounted but... |
Mounted up my Hella 500's but something is wrong with the kit. They show the switch with two connections but the one I got has three. I assume one is for ground, load and battery. The connectors provided wont even fit on them because the plastic covers are too thick. I wired them into the parking lights but not sure what to do now. I may bypass the darn relay and go direct like my last Jeep. Geez, this should have been easy! |
|
| Author: | mlr [ Tue Dec 26, 2006 4:06 pm ] |
| Post subject: | |
I had the same exact problem when installing mine. Their website has a different set of instructions: http://www.hella.com/produktion/HellaPo ... st_450.pdf Hope that helps. |
|
| Author: | Jeepjeepster [ Tue Dec 26, 2006 5:22 pm ] |
| Post subject: | |
One is for a ground to light up the little light in the switch.. Make sure you have it wired right.. Dont want to make alittle fire when you turn the switch on..
The switch that came with my hellas was labeled which was ground and everything. |
|
| Author: | garyg [ Tue Dec 26, 2006 6:18 pm ] |
| Post subject: | |
mlr wrote: I had the same exact problem when installing mine. Their website has a different set of instructions:
http://www.hella.com/produktion/HellaPo ... st_450.pdf Hope that helps. Excellent! Yea, I was shocked when I got to the switch. Everything else was clear enough. Thanks |
|
| Author: | garyg [ Tue Dec 26, 2006 6:22 pm ] |
| Post subject: | |
Jeepjeepster wrote: One is for a ground to light up the little light in the switch..
Make sure you have it wired right.. Dont want to make alittle fire when you turn the switch on.. The switch that came with my hellas was labeled which was ground and everything. Mine was labeled too but like I said, the instructions showed only two posts. Besides, the thick plastic covers over the connectors would not allow me to put them on the swith together. As if they were the wrong parts or something. Hopefully there wont be any fires 
|
|
| Author: | 2372ighost [ Wed Dec 27, 2006 12:27 am ] |
| Post subject: | |
I just bent the outside bayonets 30degrees and the clips fit fine. |
|
| Author: | action [ Thu Dec 28, 2006 1:58 pm ] |
| Post subject: | |
I never use the crap connectors that come with the kits, I use my own crimp on conenctors and Heat shrink over them. Its neater, not as thick and more secure. Outside the cab, I solder them too. I also usually swap out the fuse holder that comes with the kit for a blade style one that matches the factory fuses, and with a rubber cover. A little dielectric grease on terminals helps alot too! |
|
| Author: | Cacher123 [ Thu Dec 28, 2006 3:54 pm ] |
| Post subject: | |
The clips will work if u bend the top and bottom contact up/down a little. They do push on. If u wire the switch wrong it will either always light (wrong) or only light when the switch is on. |
|
| Author: | garyg [ Fri Dec 29, 2006 3:35 pm ] |
| Post subject: | |
2372ighost wrote: I just bent the outside bayonets 30degrees and the clips fit fine.
Seems lame to have to alter stuff though 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|