Let me be the first...............
AMEN!!!!!!!
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| CV Joint Split Boot! http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=15991 |
Page 1 of 1 |
| Author: | Jeepin Al [ Thu Dec 28, 2006 11:07 pm ] |
| Post subject: | CV Joint Split Boot! |
Halleluia Brothers and Sisters....I have found a split boot that will work on our KJ's....can I have an A-MEN!! EMPI Inc's 86-2858-C will work on our inner boots. And it looks like the outter too. After a trail ride a couple of weeks ago, I really tore up my boots. It is a good thing I fill them up with grease, I flung grease all over the place, and when I cut the old boot away, there was enough grease in the CV joint to go another 500 miles! EMPI, the same guys that sell HP Volks stuff make or import boots. They are screw together units. I did put a little silicon along the joint, but you don't need to. I found this guy in Maryland....CV Restoration, he has them in stock, in fact I am going to order two more to carry with me. WWW.THECVMAN.COM $24.95 each, and he has the solid units too, when the spring rolls around I will replace the split boots with the solid ones. It took me about an hour to change the one driver's side boot. I am little out of practice. Tell him I sent you, so he knows I put the word out!! Al |
|
| Author: | psinsyd [ Thu Dec 28, 2006 11:18 pm ] |
| Post subject: | |
Let me be the first............... AMEN!!!!!!!
|
|
| Author: | LiLredLibby [ Thu Dec 28, 2006 11:23 pm ] |
| Post subject: | |
Hey Al,...That is great news.I work in an independent shop and we've used those for a while,but we ran across another setup where you can purchase an air operated finger tool that goes into the small end of a specially made boot and expands it large enough to fit over the large end first.I know it sounds crazy but it works really fine.Plus the boot material is very plyable yet very strong.It holds up real well,at least on normally driven vehicles with proper cv angels.Ever seen one? 
|
|
| Author: | FreedomKJ [ Thu Dec 28, 2006 11:25 pm ] |
| Post subject: | |
Great news! Can you add this info somewhere that it won't vanish in the mass of posts? I don't need boots yet, but I'm sure I will someday. |
|
| Author: | Jeepin Al [ Fri Dec 29, 2006 9:11 am ] |
| Post subject: | |
Hey Ron, no I have never seen one of those ther darn contraptions! If I am ever in the area I will nedd to stop buy and check it out. Al |
|
| Author: | Gris [ Fri Dec 29, 2006 9:39 am ] |
| Post subject: | |
THis is awsome. I just sent him an email. My Libby has the terrible habit of eating the driver's-side outer boot EVERY time I go off-road. |
|
| Author: | meh_kick [ Fri Dec 29, 2006 11:00 am ] |
| Post subject: | |
Out of curiosity what does the MOPAR part usually cost. Dealer wanted to charge me $80 (parts and labor) to replace the outer passenger boot. (I'm arguing that it was pinched/punctured during the ball joint recall, or another warranty service). This sounds like a great alternative I'd be willing to try myself to bypass my crappy dealer. |
|
| Author: | Elwenil [ Fri Dec 29, 2006 5:49 pm ] |
| Post subject: | |
For an '04 the outer number is 5066025AB and lists for $69.60 and the inner is part number 5066024AA and lists for $29.75. |
|
| Author: | Jeepin Al [ Fri Dec 29, 2006 10:52 pm ] |
| Post subject: | |
Ok ladies and gents, I just got done with the second install. All went well. The boots will fit the outer CV's but I don't know how long they will last since they need to move 360 instead on just 180 like the inboard ones do (meaning the outers need to stear, immmmm steak, too). The only problem I will have is with one of the little tabs will most likely get ripped off by the Rock Krawler clevis, since they are much wider than the stock sticks. Al |
|
| Author: | thebenagade [ Sat Dec 30, 2006 12:28 am ] |
| Post subject: | |
if you are in the akron/cleveland ohio area the folks at L.A. Products will have the boots too. I think the actual city they are in is greene not for sure but it is a little north of akron. |
|
| Author: | LiLredLibby [ Sat Dec 30, 2006 1:09 am ] |
| Post subject: | |
[quote="Jeepin Al"]Hey Ron, no I have never seen one of those ther darn contraptions! If I am ever in the area I will nedd to stop buy and check it out. Hey Al,...When you get a chance,go onto E-bay,and search item number 4444545003. It will be one of those contraptions I was tellin you about that stretches the fire out of a cv boot to fit the little end of the boot over the big end of the joint.The boot for this tool is made from a material simular to that of a sling shot(medical tubbing?).Very stretchy and long lasting 
|
|
| Author: | Jeepin Al [ Sat Dec 30, 2006 12:20 pm ] |
| Post subject: | |
Wow that tool is really neat, so you remove the axel, and you don't need to take the CV off to install the boot. I may just need to buy one. Hpw cool is that! Al |
|
| Author: | GregScuba [ Thu Jan 11, 2007 1:03 pm ] |
| Post subject: | |
Sweet! this is great info. Thank you! |
|
| Author: | Guyute1210 [ Fri Jan 12, 2007 4:07 pm ] |
| Post subject: | |
LiLredLibby wrote: Jeepin Al wrote: Hey Ron, no I have never seen one of those ther darn contraptions! If I am ever in the area I will nedd to stop buy and check it out. Hey Al,...When you get a chance,go onto E-bay,and search item number 4444545003. It will be one of those contraptions I was tellin you about that stretches the fire out of a cv boot to fit the little end of the boot over the big end of the joint.The boot for this tool is made from a material simular to that of a sling shot(medical tubbing?).Very stretchy and long lasting I saw that contraption on 2 guys garage on speed channel...they did a whole show on boots and replacing them...that tool is (as the guys downunder put it) ducks nuts! |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|