There should be a nut and bolt that help to flare the nutzert when torqued to 30 ft. lbs.
Here are the parts that you should have:
Here are the directions to flare the nutzerts:
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Help on skids http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=18655 |
Page 1 of 1 |
| Author: | BCool [ Sat Mar 17, 2007 11:18 am ] |
| Post subject: | Help on skids |
Im trying to install my skids. The holes are hex and the nutzerts are round, how is this supposed to work, do you pound them in? |
|
| Author: | meh_kick [ Sat Mar 17, 2007 11:31 am ] |
| Post subject: | |
There should be a nut and bolt that help to flare the nutzert when torqued to 30 ft. lbs. Here are the parts that you should have:
Here are the directions to flare the nutzerts:
|
|
| Author: | chetos [ Sat Mar 17, 2007 11:33 am ] |
| Post subject: | Re: Help on skids |
BCool wrote: Im trying to install my skids. The holes are hex and the nutzerts are round, how is this supposed to work, do you pound them in?
Sounds like you need the hex nutzerts. You got the wrong nutzerts. You can order these from the dealer. About a buck apiece. |
|
| Author: | meh_kick [ Sat Mar 17, 2007 11:34 am ] |
| Post subject: | |
Oh, this may go with out saying. But be sure to insert the nutzert BEFORE you torque the two pieces. |
|
| Author: | BCool [ Sat Mar 17, 2007 11:36 am ] |
| Post subject: | |
Ok, I have the tool and the nutserts. So there are hex ones? Mine are round and will not fit into the hex holes in the frame, bummer cause I ordered the skids and this is what came with them. |
|
| Author: | chetos [ Sat Mar 17, 2007 11:45 am ] |
| Post subject: | |
The hex number is: 06506644AA |
|
| Author: | jason thompson [ Sat Mar 17, 2007 12:55 pm ] |
| Post subject: | |
easy drill hex hole round ,insert round nut zert and procede I do not know what size hole you should drill but the nut zert should fit snug but do not pound it in as you tighten the nut zert the part in the unibody or cross member will flair holding it tighter then the top side will flair hope this helps PS HOLD ON TO THE DRILL TIGHT and take your time drilling it will want to get away from you drilling out a hex hole |
|
| Author: | BCool [ Sat Mar 17, 2007 3:54 pm ] |
| Post subject: | thanks everyone |
After much tribulation I noticed that the nutserts in the bag with bolts were hex, I was using the one that came with the tool |
|
| Author: | BCool [ Sat Mar 17, 2007 3:55 pm ] |
| Post subject: | thanks everyone |
After much tribulation I noticed that the nutserts in the bag with bolts were hex, I was using the one that came with the tool |
|
| Author: | Jeepjeepster [ Sat Mar 17, 2007 4:54 pm ] |
| Post subject: | Re: thanks everyone |
BCool wrote: After much tribulation I noticed that the nutserts in the bag with bolts were hex, I was using the one that came with the tool
haha, yea, I noticed one of them was different than the others also. I never could figure out what they sent that one with the kit though? 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|