LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Dash Board Bezels
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=22545		 Page 1 of 1
Author:  WoodysKJ [ Sun Jul 15, 2007 3:02 pm ]
Post subject:  Dash Board Bezels
Anybody out there know the part number for the left side insturment panel bezel? I believe it is where the Roof Light switch is located. I am going to install some lights and want to locate the switch there. I have mine removed and it shows an area for the switch to be cut in.

Image

Existing Part Number:
Image

Switch location on inside:
Image

Does anybody know how to tell from the many part numbers listed in the part sheet Which one is for a grey interoir and has this location already cut out ready to add the switch?

Anybody have one to sell?
Author:  Jeepjeepster [ Sun Jul 15, 2007 4:10 pm ]
Post subject: 
I caught one for free in the for sale section, I had the same thing in mind as you do. I have extra lights on the front and wanted it to appear stock from the inside.

My idea was kinda shot down when I looked at the price for the switch that goes in that hole! $30!!!!!! It has a relay and fuses in in one.. :shock:
Author:  jason thompson [ Sun Jul 15, 2007 4:21 pm ]
Post subject: 
what about a flush mount type swich and cut it with a dremel tool?
that is how I mounted the swiches for the ARB
Author:  WoodysKJ [ Sun Jul 15, 2007 4:34 pm ]
Post subject: 
Sounds good.

I need pics.

I am looking for a spare bezel so I can do the surgry needed and still have a fall back.

jeepjeepster, Pics of your switch?
Author:  tjkoen01 [ Mon Jul 16, 2007 8:29 am ]
Post subject: 
I shaved the factory switch mount off of the back of mine and got some chrome toggle switches from radio hut, drilled holes and presto! I opted for the RS switches b/c I wanted all my switches to match and needed a single pole, double throw with a center off.
Author:  WoodysKJ [ Mon Jul 16, 2007 9:41 am ]
Post subject: 
PICS PLEASE!!!!
Author:  CaKJFreedom [ Mon Jul 16, 2007 12:28 pm ]
Post subject: 
I just dremel'd mine too. Got a small switch from Auto Zone. Don't do it in the kitchen, there'll be plastic dust everywhere and you get in trouble.

Image
Image
Image
Image
Author:  WoodysKJ [ Mon Jul 16, 2007 12:33 pm ]
Post subject: 
Nanette,

Thats a COOL looking switch!!!!!!!!!! best one i have ever seen, where at AutoZone? it came with the beauty ring?

What is it rated? How many lights do you run off it and the relay?

I could see a few of those. VERY descreat and clean.

GREAT job!!!
Author:  pokefan [ Mon Jul 16, 2007 12:34 pm ]
Post subject: 
CaKJFreedom wrote:
Don't do it in the kitchen, there'll be plastic dust everywhere and you get in trouble.

X2


Quote:
Image

I was going to post pics of mine but that's exactly how mine looks.
Author:  Jeepjeepster [ Mon Jul 16, 2007 1:00 pm ]
Post subject: 
Ive got the same switch but Ive yet to put it in. 5 bought mine at Advance auto parts for around $5 or so.

I dont have any pics of that woody.. :?
Author:  Gris [ Mon Jul 16, 2007 1:35 pm ]
Post subject: 
I dremeled mine. Cheaper than buying a new one.

Image
Author:  Maximum Carnage [ Mon Jul 16, 2007 1:52 pm ]
Post subject: 
CaKJFreedom wrote:
Image


The same switch came with my Hella FF75. I too have a switch in this area.
Author:  CaKJFreedom [ Wed Jul 18, 2007 12:48 pm ]
Post subject: 
Glad I could save you a step pokefan. It's a cool little switch, just a couple bucks and yes, the ring is part of it. I love any reason to dremel....

I don't remember what it's rated. There's a relay and four lights work off of it.
Author:  riptricket [ Wed Jul 18, 2007 3:11 pm ]
Post subject: 
what accssory did you hook into your dremel to make such a clean circle?
Author:  pokefan [ Wed Jul 18, 2007 6:29 pm ]
Post subject: 
lol, My way was a little ghetto but I got a finishing buff and opened up the hole enough with a drill to get it in there and then just let it spin and open up the hole. Little primitive but it worked :lol:
Author:  CaKJFreedom [ Thu Jul 19, 2007 7:30 pm ]
Post subject: 
It's actually a Black and Decker generic Dremel. It has an attachment that's a circle about a half inch thick. Kind of like a stack of dimes that'll cut stuff. I marked the center, drilled it out, then just used the circle part until it was big enough. I'm anal about some stuff and that helped.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/