Thanks JJ I'll do that today or tomorrow. You da man
So do I have the sizes right? 12mm and 14mm?
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Tool needed to take out my fill/drain plugs on manual trans? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=23571 |
Page 1 of 1 |
| Author: | BeepBeepJeepJeep [ Sat Aug 18, 2007 9:20 am ] |
| Post subject: | Tool needed to take out my fill/drain plugs on manual trans? |
It looks like I need a 12mil allen wrench or something for the one and maybe even a 13 or a 14 for the other :O Any one have any idea what I need here? Why didn't they make all the plugs the same? Grrrrrrrr |
|
| Author: | JJsTJ [ Sat Aug 18, 2007 12:07 pm ] |
| Post subject: | |
Go to Harbor Freight or similar discount tool store and get hooked up. BRICK, NJ 2770 HOOPER AVE, STE 1 732-477-5300 SADDLE BROOK, NJ 441 MARKET ST 201-587-0700 VINELAND, NJ 20 WEST PARK AVE 856-691-4200 |
|
| Author: | BeepBeepJeepJeep [ Sat Aug 18, 2007 12:22 pm ] |
| Post subject: | |
Thanks JJ I'll do that today or tomorrow. You da man
So do I have the sizes right? 12mm and 14mm? |
|
| Author: | JJsTJ [ Sat Aug 18, 2007 1:06 pm ] |
| Post subject: | |
Really not sure on sizes. I winged it and got lucky but don't recall what I used. If I had a manual trans KJ I would figure it out. Make sure you take your KJ w/ you and I bet they will let you run in and out of the store w/ different sizes to make sure they fit. At least I know my local store would. |
|
| Author: | Cowcatcher [ Sat Aug 18, 2007 4:21 pm ] |
| Post subject: | |
Funny, bought some at HF today myself. I actually went in to buy a 17MM 1/2" socket I needed for installing my skids, or a 3/8" torque wrench (Yes, of course I bought both. They were on sale after all!!!!!  ). While there I picked up a set of metric hex sockets. $10 for 3/8" - 4,5,6,7,8,10mm think the next set added three 1/2" sizes larger for $16.99.
|
|
| Author: | hooperswish [ Sun Aug 19, 2007 9:17 am ] |
| Post subject: | |
If you have the nsg 370 6 speed, it takes 17mm for the drain, and 14 mm for the fill. These hex sockets are cheap at autozone. Check out my experience: http://www.lostjeeps.com/forum/phpBB3/vie ... ansmission Good luck....fun, easy project that shows positive immediate results. 
|
|
| Author: | fmc1 [ Mon Aug 20, 2007 11:27 am ] |
| Post subject: | |
On an 03 5-speed both plugs are the same size 17mm. |
|
| Author: | BeepBeepJeepJeep [ Mon Aug 20, 2007 11:28 am ] |
| Post subject: | |
hooperswish wrote: If you have the nsg 370 6 speed, it takes 17mm for the drain, and 14 mm for the fill. These hex sockets are cheap at autozone.
Check out my experience: http://www.lostjeeps.com/forum/phpBB3/vie ... ansmission Good luck....fun, easy project that shows positive immediate results. Thanks a bunch. Bill |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|