LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Skink sliders / rock rails
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=30755		 Page 1 of 1
Author:  tonycrd [ Thu Mar 20, 2008 11:49 am ]
Post subject:  Skink sliders / rock rails
Can anybody tell me how you mount those to the unibody? With nutzerts?
Author:  Jeepjeepster [ Thu Mar 20, 2008 12:05 pm ]
Post subject: 
Drill holes in pinch weld and frame then use self tapping screws for the frame and bolts w/nuts for the pinch seam.
Author:  tonycrd [ Thu Mar 20, 2008 12:10 pm ]
Post subject: 
self tapping screws work? isn't the metal a bit thin for those?
Author:  hatu [ Thu Mar 20, 2008 1:00 pm ]
Post subject: 
For the Boulder Bar frame holes, it seemed to be anywhere from about an 1/8 to 3/16 think depending where the holes lined up with the frame. The self tapping screws worked great. Just don't over tighten...
Author:  moose [ Thu Mar 20, 2008 2:23 pm ]
Post subject: 
doesn't marty have a install guide on his website?
Author:  Jeepjeepster [ Thu Mar 20, 2008 2:47 pm ]
Post subject: 
Ive got self tapping screws in mine and they work out great tony.

Like hatu said, make sure you dont over tighten them.
Author:  Maximum Carnage [ Thu Mar 20, 2008 3:36 pm ]
Post subject: 
Mine came with bolts and nuts for the pinch weld. Personally I won't use self tap screws. I agree, ** self tap screws never over tight **
Author:  KW AV8R [ Thu Mar 20, 2008 6:38 pm ]
Post subject: 
I have a set of prototype skink sliders. They are held to the pinch seam with nuts and bolts and held to the "frame rails" with self-tapping bolts. I have dropped the whole weight of the KJ on them numerous times both in the Colorado Rockies and at Moab and they never budged, came loose, bent, or had to be re-tightened. I fully expect them to outlast my KJ with minimal maintenance (re-painting/powdercoating).
Author:  dieselenthusiast [ Thu Mar 20, 2008 10:10 pm ]
Post subject: 
KW AV8R wrote:
I have a set of prototype skink sliders. They are held to the pinch seam with nuts and bolts and held to the "frame rails" with self-tapping bolts. I have dropped the whole weight of the KJ on them numerous times both in the Colorado Rockies and at Moab and they never budged, came loose, bent, or had to be re-tightened. I fully expect them to outlast my KJ with minimal maintenance (re-painting/powdercoating).


I am a witness to Pete. These LOST ROCKIES guys/girls are Serious! It’s a Rocky Mountain disease that they carry, so DO NOT let them bite you when you see them at Moab or they will pass the disease to you. Symptoms of the Rocky Mountain disease is the feeling that you’re a mountain goat and you can Climb anything with your KJ. However, I can guarantee that Rock Lizard’s products are built to last. And I can honestly say that these products are field tested!
Author:  tjkj2002 [ Thu Mar 20, 2008 10:17 pm ]
Post subject: 
I have the Super Skink slider(from RL of course :wink: ).I hate self tapping bolts,they have there use but I still don't like them since they are grade 2.I used through bolts(3/8" grade 8's) where I could get to the inside of the "frame",all but 4(out of 12) of my bolts are 3/8" grade 8 through bolts and the 4 are self tappers,only cause I couldn't get access to the inside of the "frame".

With my custom belly pan for my SFA swap will allow me to use through bolts for all the "frame" mounting locations for my rock rails.
Author:  LostEddie [ Fri Mar 21, 2008 3:54 pm ]
Post subject: 
Here is my write-up that may help. Includes link to RL install instructions.
http://www.lostjeeps.com/forum/phpBB3/vie ... ht=#277248
Author:  riptricket [ Sat Mar 22, 2008 12:57 am ]
Post subject: 
I WANT MY RL SUPER SLIDERS SOOOOOO BADLY!!!!!!
I HAVE BEEN WAITING AND WAITING!
AHHHHHHHHHHHHHH IT'S DRIVING ME CRAZY!
but i guess i'll have to get on with life....
Author:  KW AV8R [ Sat Mar 22, 2008 8:02 pm ]
Post subject: 
All good things come to those that wait ....... :wink:
Author:  callaway [ Sat Mar 22, 2008 8:26 pm ]
Post subject: 
i have 1/4-20s w/nylocks on the pinch weld and then 1/2" (i think?) self threading bolts going into the frameon my boulder bars
Author:  tonycrd [ Mon Mar 24, 2008 6:33 am ]
Post subject: 
So for those who do not want to use self tappers:

When I fitted my sidebars I pulled the bolts through the mounting holes from the underside of the Unibody. There are some big holes (factory punched) there.

What do you do? Drill the mounting holes. Get a piece of thin wire like from your wife's nitting and sewing box.

Put the wire through the hole, then through the hole in the bottom of the unibody. Tie the bolts to them, at the thread end.

Fit your sliders or bars or whatever, now gently pull the bolts through the holes. Lower the mounting plate of the sliders so they 'guillotine' the bolts in order to hold them in place. Fit nuts. Done.

Image
Author:  snowsport [ Mon Mar 24, 2008 12:04 pm ]
Post subject: 
Great idea! Needle nose vice grips could work to hold them still while you tighten the nuts, as long as you don't crush the threads....I had to do that on something recently, but I don't recall what the project was...
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/