LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

rusty skinks
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=32005		 Page 1 of 1
Author:  riptricket [ Tue Apr 29, 2008 12:55 am ]
Post subject:  rusty skinks
alright guys... i have a family problem right now, and will not be able to put on my skinks for a week atleast, and they have quite a lot of surface rust. is it okay to go a couple more weeks, even a month without having them line-xed... will they be okay?

i still have one to drill out and just don't have the time or the persons.
Author:  JPaul [ Tue Apr 29, 2008 1:57 am ]
Post subject: 
Sorry to hear your facing some challenges.

I think they will be fine, it's only a couple weeks, and I'm guessing it's not like they are sitting next to the ocean or anything like that. Surface rust really isn't a big deal, sandblasting, whire wheel, flap wheel, 3m stripper wheels, sandpaper, naval jelly, all that kind of stuff will knock surface rust right off in a jiffy. Well, maybe not the sand paper, that might take a bit of work.

I'd only worry if the rust is starting to pit the metal, but heck, they are armor anyway, it's not like you are chrome plating the suckers. They will eventually be rusted peices of metal anyway.

One thing you could do is spray them down with wd-40 or something similar and wrap them in plastic. That might help slow down the rusting process, though you would hten have to thoroughly clean the oil off before you paint them, otherwise you'll have bigger problems.
Author:  Jeepjeepster [ Tue Apr 29, 2008 9:58 am ]
Post subject: 
They will be fine. Thats thick metal, not thin sheet metal so they could rust for awhile and be just fine.

Just dont let it go on for years.
Author:  jsc7002 [ Tue Apr 29, 2008 11:59 am ]
Post subject: 
ya they will be fine, but if you can do spray them w/ wd40 itll make it easier to clean them up when you go to install them
Author:  Fouros [ Tue Apr 29, 2008 7:59 pm ]
Post subject: 
or you could get some rust converter and primer coat them in that and they are good for 12 months
Author:  Guest [ Tue Apr 29, 2008 10:33 pm ]
Post subject: 
jsc7002 wrote:
ya they will be fine, but if you can do spray them w/ wd40 itll make it easier to clean them up when you go to install them


Yes, and the WD40 will make the paint/coating stick EXTREMELY WELL :lol: (Not really)
Author:  jsc7002 [ Tue Apr 29, 2008 10:38 pm ]
Post subject: 
ThunderbirdJunkie wrote:
jsc7002 wrote:
ya they will be fine, but if you can do spray them w/ wd40 itll make it easier to clean them up when you go to install them


Yes, and the WD40 will make the paint/coating stick EXTREMELY WELL :lol: (Not really)


lol true, but it would keep the surface rust off and besides hes gonna need to clean them before he paints them :wink:
Author:  AndySRT [ Tue Apr 29, 2008 11:35 pm ]
Post subject: 
first off sorry to hear about family problems. you will be fine. a little surface rust wont hurt the line X coating they prime them before hand. but i would reccomend against getting them line Xed or bedlined at all. the stuff just rips off the first time they hit anything. I had mine line Xed on my old bronco and the stuff just tore off the first time i used them to slide over something while off roading. Just paint them and you will be good for all your off roading excursions and just re spray them after use. just my opinion.
Author:  Rush345 [ Wed Apr 30, 2008 1:32 am ]
Post subject: 
Before you apply any Top Coat I would suggest a coating of POR 15 this Rust Primer will reacte with existing rust and when finished will be bullet proof. They sell a kit for $25.00 that should be just enough to coat your sliders. It's their starter kit. But should do the job desired. :twisted: :twisted: :twisted:
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/