LOST JEEPS :: View topic - light bar part numbers

My Renegade light bar arrived yesterday - with the following missing (for ease in determining what items are missing, I will refer to the items by the letter given to them in the following Mopar instructions http://site.justforjeeps.com/guide/82206126AB.pdf )

items missing : B, C, E, G, I , K, O, P
on the plus side, all the wiring was included

Please help me figure out part numbers and/or what I need to buy!

Here I come to save the dayyyyyy

B is a 10mm exterior / 6 mm interior nutzert, sorta lika rivet but holds thread for a 6 mm bolt or stud.

C is the 'free' MOPAR nutzert fitting tool, you don't need that you can just use a long 6mm bolt and a nut.

E are the MOPAR fitting bolts, these hold the light bar on the roof. You don't need those either, buy regular 6mm bolts

G you do need these, actualy 4 of them, they hold the plastic top cover on the light bar.

I tie-wraps, available in any hardware store

K is shrink wrap, you use this to isolate the wires, see pic 31 in the manual

O + P are the socket for the LED. If you have the lightbar thingy already in your dash you don't need this.

K+O+P should be taped to the wiring harness in al little plastic baggy..( maybe not there ).

Ok, here's my howto and the howto on the dash:

http://www.jeepkj.com/forum/showthread.php?t=34988

http://www.jeepkj.com/forum/showthread.php?t=34988

Here I come to save the dayyyyyy Very Happy

B is a 10mm exterior / 6 mm interior nutzert, sorta lika rivet but holds thread for a 6 mm bolt or stud.

C is the 'free' MOPAR nutzert fitting tool, you don't need that you can just use a long 6mm bolt and a nut.

E are the MOPAR fitting bolts, these hold the light bar on the roof. You don't need those either, buy regular 6mm bolts

G you do need these, actualy 4 of them, they hold the plastic top cover on the light bar.

I tie-wraps, available in any hardware store

K is shrink wrap, you use this to isolate the wires, see pic 31 in the manual

O + P are the socket for the LED. If you have the lightbar thingy already in your dash you don't need this.

K+O+P should be taped to the wiring harness in al little plastic baggy..( maybe not there ).

Ok, here's my howto and the howto on the dash:

Author:	lionseye640 [ Thu Aug 21, 2008 8:48 am ]
Post subject:	light bar part numbers
My Renegade light bar arrived yesterday - with the following missing (for ease in determining what items are missing, I will refer to the items by the letter given to them in the following Mopar instructions http://site.justforjeeps.com/guide/82206126AB.pdf ) items missing : B, C, E, G, I , K, O, P on the plus side, all the wiring was included Please help me figure out part numbers and/or what I need to buy!

Author:	lionseye640 [ Thu Aug 21, 2008 10:32 am ]
Post subject:
Someone's got to have an answer for me

Author:	pokefan [ Thu Aug 21, 2008 11:00 am ]
Post subject:
Most of it looks like it could be had at a hardware store but since they didn't list sizes on anything it's kind of hard to say what you would need.

Author:	lionseye640 [ Thu Aug 21, 2008 11:08 am ]
Post subject:
That's why I was really hoping that someone who had done the install might have some idea of what I need to pick up, rather than me just guessing (which never works out well)

Author:	Sir Sam [ Thu Aug 21, 2008 12:26 pm ]
Post subject:	Re: light bar part numbers
lionseye640 wrote: My Renegade light bar arrived yesterday - with the following missing (for ease in determining what items are missing, I will refer to the items by the letter given to them in the following Mopar instructions http://site.justforjeeps.com/guide/82206126AB.pdf ) items missing : B, C, E, G, I , K, O, P on the plus side, all the wiring was included Please help me figure out part numbers and/or what I need to buy! Did you buy the whole kit or just the lightbar.... AFAIK all those parts you are missing are sold seperately.......look in the parts fiches and you should find them there.

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

light bar part numbers http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=35269	Page 1 of 1

Author:	lionseye640 [ Thu Aug 21, 2008 12:32 pm ]
Post subject:
I bought the whole thing from a member here who bought it off ebay (or something like that) - member was unaware parts were missing since they never opened the plastic bags in the box. Not a huge deal, but a bit of a pain to sort out. Heck, from the diagram on the instructions, I can't even tell what a couple of the parts actually are

Author:	callaway [ Thu Aug 21, 2008 3:30 pm ]
Post subject:
Check out the parts department at a dealership. Theres a jeep dealer on 90 in Glencoe ( just north of willow road on the west side of the highway )

Author:	lionseye640 [ Thu Aug 21, 2008 3:52 pm ]
Post subject:
There's one down the street from me (just south of Tower Road next to the Edens Expressway - wait, that's probably the one you meant ) that I'm going to go to - but some times their parts guys are idiots

Author:	501 [ Fri Aug 22, 2008 2:19 am ]
Post subject:
Contact TonyCRD, he just installed one, maybe he would know. B & C I found at a local TrueValue/ACE hardware shop. "I" are just plastic wire ties. But I'd check with Tony, he should be able to help.

Author:	tonycrd [ Fri Aug 22, 2008 8:01 am ]
Post subject:
Here I come to save the dayyyyyy B is a 10mm exterior / 6 mm interior nutzert, sorta lika rivet but holds thread for a 6 mm bolt or stud. C is the 'free' MOPAR nutzert fitting tool, you don't need that you can just use a long 6mm bolt and a nut. E are the MOPAR fitting bolts, these hold the light bar on the roof. You don't need those either, buy regular 6mm bolts G you do need these, actualy 4 of them, they hold the plastic top cover on the light bar. I tie-wraps, available in any hardware store K is shrink wrap, you use this to isolate the wires, see pic 31 in the manual O + P are the socket for the LED. If you have the lightbar thingy already in your dash you don't need this. K+O+P should be taped to the wiring harness in al little plastic baggy..( maybe not there ). Ok, here's my howto and the howto on the dash: http://www.jeepkj.com/forum/showthread.php?t=34988 http://www.jeepkj.com/forum/showthread.php?t=34988

Author:	BeepBeepJeepJeep [ Fri Aug 22, 2008 8:04 am ]
Post subject:
tonycrd wrote: Here I come to save the dayyyyyy B is a 10mm exterior / 6 mm interior nutzert, sorta lika rivet but holds thread for a 6 mm bolt or stud. C is the 'free' MOPAR nutzert fitting tool, you don't need that you can just use a long 6mm bolt and a nut. E are the MOPAR fitting bolts, these hold the light bar on the roof. You don't need those either, buy regular 6mm bolts G you do need these, actualy 4 of them, they hold the plastic top cover on the light bar. I tie-wraps, available in any hardware store K is shrink wrap, you use this to isolate the wires, see pic 31 in the manual O + P are the socket for the LED. If you have the lightbar thingy already in your dash you don't need this. K+O+P should be taped to the wiring harness in al little plastic baggy..( maybe not there ). Ok, here's my howto and the howto on the dash: http://www.jeepkj.com/forum/showthread.php?t=34988 http://www.jeepkj.com/forum/showthread.php?t=34988 Get this man a beer.

Author:	lionseye640 [ Fri Aug 22, 2008 8:45 am ]
Post subject:
Quote: Here I come to save the dayyyyyy Very Happy B is a 10mm exterior / 6 mm interior nutzert, sorta lika rivet but holds thread for a 6 mm bolt or stud. C is the 'free' MOPAR nutzert fitting tool, you don't need that you can just use a long 6mm bolt and a nut. E are the MOPAR fitting bolts, these hold the light bar on the roof. You don't need those either, buy regular 6mm bolts G you do need these, actualy 4 of them, they hold the plastic top cover on the light bar. I tie-wraps, available in any hardware store K is shrink wrap, you use this to isolate the wires, see pic 31 in the manual O + P are the socket for the LED. If you have the lightbar thingy already in your dash you don't need this. K+O+P should be taped to the wiring harness in al little plastic baggy..( maybe not there ). Ok, here's my howto and the howto on the dash: If you lived in the US I'd buy you a case of beer! Thank you!!![/url]

Author:	tonycrd [ Fri Aug 22, 2008 9:21 am ]
Post subject:
Thanks....! If only I lived in the states Anyway, here's the part number for the top cover bolts...06507783AA. You'll need four of those.

Author:	lionseye640 [ Fri Aug 22, 2008 9:26 am ]
Post subject:
You're the best!

Page 1 of 1	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/

Author:	501 [ Fri Aug 22, 2008 6:23 pm ]
Post subject:
I had a feeling Tony would be able to help!