LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Nutzerts
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=35430		 Page 1 of 2
Author:  06 KJ Sport [ Tue Aug 26, 2008 5:03 pm ]
Post subject:  Nutzerts
Now I know what they are and where they are supposed to go, so I guess my questions is How well do the nutzerts hold up? I just installed them for my skids and am going to install them for my sliders, but I just want to make sure they are going to hold up under the up and down force of the sliders...
Author:  JL Rockies [ Tue Aug 26, 2008 5:29 pm ]
Post subject: 
My MOPAR sliders are dented and somewhat bent, but the nutzerts never budged.
Author:  jason thompson [ Tue Aug 26, 2008 6:54 pm ]
Post subject: 
the ones on the front shovel
I mean front skid held up just fine pre-lift
they also held a good 50# of mud for a 100+ mile drive in the same skid

The T-case skid and Tranny skid are both held by nutzerts AND 1/2" carriage bolts so I dont really count them as stock
and the fuel tank skid is held on by the hitch so I know it aint going no place
Author:  Maximum Carnage [ Tue Aug 26, 2008 8:16 pm ]
Post subject: 
Supposedly there are two different types of nutzerts, what is the difference and what are their part numbers?
Author:  jsc7002 [ Tue Aug 26, 2008 8:16 pm ]
Post subject: 
I thought the difference was in the size
Author:  06 KJ Sport [ Tue Aug 26, 2008 11:21 pm ]
Post subject: 
The ones I ordered from Jeep would fit into any nutzert hole. They were also made from aluminum...I think :?
Author:  rescu2000 [ Wed Aug 27, 2008 3:37 am ]
Post subject: 
I personally am not a fan. I have had one spin out on me. It was a pain in the butt to get the bolt out. I don't recall whether I had used an impact wrench on it or not, but I don't think I did. I guess most people don't have problems with them, but the last thing I want to do is be out on a trail and need to get a skid off and have to fight with a spinning insert. I haven't replaced all of mine, but as I take skids off for any reason, I replace the inserts with Nuts and Bolts.
Author:  Maximum Carnage [ Wed Aug 27, 2008 8:02 am ]
Post subject: 
06 KJ Sport wrote:
The ones I ordered from Jeep would fit into any nutzert hole. They were also made from aluminum...I think :?


Do you have a part number?
Author:  jsc7002 [ Wed Aug 27, 2008 2:21 pm ]
Post subject: 
they arent aluminum unless you got some different ones, and when I installed some I got the welder out too and put a bead around them also so I know they arent going anywhere
Author:  Albert [ Wed Aug 27, 2008 7:58 pm ]
Post subject: 
Maximum Carnage wrote:
Supposedly there are two different types of nutzerts, what is the difference and what are their part numbers?


I didn't know there were 2 different types. When I got my skids the nutzerts and bolts came with them. After I put my skids on I got a couple of spares because I thought they were going to fall off or something. But I never used them (YET)....

I still have the nutzerts and bolts and bill from the Mopar dealer from 2 years ago,

2 each #6503571 - description 124B1 - screw - $4.50 list ($2.25 each)
2 each #6505294AA - description 124B1 - rivet - $3.90 list ($1.95 each)

It doesn't say nutzert on the bill and they look like the ones I put in. The first one says screw but it is a bolt. The second one says rivet but that is the actual nutzert. I called them nutzerts and told him what they were for when I went in to the parts guy. He just laughed and knew exactly what I was talking about and ordered them and they came in the next day on the parts truck. So I hope they are right.
Author:  06 KJ Sport [ Wed Sep 03, 2008 6:20 pm ]
Post subject: 
I just today went to the Jeep dealer to get 8 of the Nutzerts and Bolts, it was going to cost me $75.00 for them :shock: There goes Jeep doing it again!! :roll: I also went to Peterbilt and they were also about the same price!

I think that I am going to bypass the nutzert and use something else like a real bolt!! How have some of you other guys done this?? DId you drill all the way thru the frame and insert a crush sleeve? Looking for some way to attach my sliders!!
Author:  Albert [ Wed Sep 03, 2008 7:03 pm ]
Post subject: 
06 KJ Sport wrote:
I just today went to the Jeep dealer to get 8 of the Nutzerts and Bolts, it was going to cost me $75.00 for them :shock: There goes Jeep doing it again!! :roll: I also went to Peterbilt and they were also about the same price!

I think that I am going to bypass the nutzert and use something else like a real bolt!! How have some of you other guys done this?? DId you drill all the way thru the frame and insert a crush sleeve? Looking for some way to attach my sliders!!


Something wrong with those prices. I got my nutzerts and bolts from a Jeep dealer and they are only a couple of bucks apiece. Try another dealer. They must be giving you a price on the wrong thing. Read my post above.
Author:  Liberator [ Wed Sep 03, 2008 11:09 pm ]
Post subject: 
06 KJ Sport wrote:
I just today went to the Jeep dealer to get 8 of the Nutzerts and Bolts, it was going to cost me $75.00 for them :shock: There goes Jeep doing it again!! :roll:


Oh, I thought you were in Canada too. Prices are often double or more of what it is in the US given the NAFTA agreement and greedy Chrysler Canada. :roll:
Author:  06 KJ Sport [ Wed Sep 03, 2008 11:15 pm ]
Post subject: 
Albert wrote:
Maximum Carnage wrote:
Supposedly there are two different types of nutzerts, what is the difference and what are their part numbers?


2 each #6503571 - description 124B1 - screw - $4.50 list
2 each #6505294AA - description 124B1 - rivet - $3.90 list



Prices in RED are the prices that I was quoted!!

$4.50 x 8 = $35.00
$3.90 x 8 = $31.20
$66.20 w/out TAX
Author:  jsc7002 [ Wed Sep 03, 2008 11:56 pm ]
Post subject: 
buy them from the online parts store, thats where I got mine and I paid a little over a dollar for the nutzert and the bolt were about $2 each
Author:  Liberator [ Thu Sep 04, 2008 12:43 am ]
Post subject: 
jsc7002 wrote:
buy them from the online parts store, thats where I got mine and I paid a little over a dollar for the nutzert and the bolt were about $2 each


what is the website please?
Author:  06 KJ Sport [ Mon Sep 08, 2008 4:20 pm ]
Post subject: 
Anybody got that website??
Author:  jsc7002 [ Tue Sep 09, 2008 12:02 am ]
Post subject: 
ok sorry it took so long, here are the part numbers:

Nutzert (6506644AA) 1.28 each
Bolts (6506027AA) 1.61 each.

and Ill look for the website, but I dont remember it off the top of my head, sorry
Author:  ChiroKJ [ Tue Apr 28, 2009 12:00 pm ]
Post subject: 
how exactly do the nutzerts go in the cross member/what holds them in?
Author:  jsc7002 [ Tue Apr 28, 2009 1:00 pm ]
Post subject: 
ChiroKJ wrote:
how exactly do the nutzerts go in the cross member/what holds them in?


they just go in a pre-drilled hole, here is a little video that shows how they work, the ones in the video are a little different then the ones you buy for the Jeep

http://www.avdel-global.com/en/products ... tsert.html
Page 1 of 2 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/