LOST JEEPS :: View topic - SQUEEEEEEK CREEEK

Have you jacked it up yet to check everything , upper/ lower ball joints, bearings ??

tommudd wrote:

Have you jacked it up yet to check everything , upper/ lower ball joints, bearings ??

nope... how do you check for balljoints.. jack it up so the tire off the ground grab it and see if it tilts in/out?

interesting.. never heard of that one. i'm always iffy on using petroleum based stuff on anything with rubber.. since it eats away at the rubber... i'm a little more easy about WD-40 since it's all natural and doesnt seem to harm things i put it on.

2006 KJ wrote:

Have the CREEEEEK from hell here too. Narrowed mine down to the sway bar bushings. They are fairly new bushings and thought it would go away. 8K later... and a little silicon spray. hahahaha even worse!!!! So why no petroleum based stuff? I was thinking a little Vaseline or something of the sort. Is this not a good idea?

Author:	2006 KJ [ Wed May 20, 2009 8:36 pm ]
Post subject:	SQUEEEEEEK CREEEK
it's driving me NUTS!!!! i have a creeeeek squeeeeek creek creeek squeeeek noise coming from my right front suspension. i think it 'may' be the upper ball joint... when i even bump the steering wheel it makes the noise when the tires roll over pebbles it makes the noise.. literally EVERYTHING make it squeek and creek. anyone else have this problem? it is driving me nuts.. i like my jeep to be silent (except tires of course ). so anyone have any input? anything i can do to stop it... is that actually the source... anyone have experience with this? if i put my hand on the bumper and push down it does it.. and i can tell it's coming from behind the wheel... might be the shock? but i still kinda think it's one of the ball joints.. top i'd guess. i have stock arms and 21000 miles on a frankenlift.

Author:	bizlimpkit [ Wed May 20, 2009 8:47 pm ]
Post subject:
i had a squek like what your saying and it ended up being the tie rod in the front ; just sprayyed it down with wd40 and problem solved

Author:	jeepkj02 [ Wed May 20, 2009 8:51 pm ]
Post subject:
You sprayed WD40 on your tie rod end....thats not good!!

Author:	Kdabbagh [ Wed May 20, 2009 8:55 pm ]
Post subject:
i had that for a while, was told it was probably the bushings, went away on its own though.

Author:	bizlimpkit [ Wed May 20, 2009 8:56 pm ]
Post subject:
did that about 4 months ago and nothing has happened...

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

SQUEEEEEEK CREEEK http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=43371	Page 1 of 1

Author:	2006 KJ [ Wed May 20, 2009 8:57 pm ]
Post subject:
i'm about to soak everything!!! just so that noise stops... i'll take a look at the tierod.. make sure nothing looks.. rotted or excessively rusty.

Author:	sleeve84028 [ Wed May 20, 2009 9:33 pm ]
Post subject:
If it doesn't squeak, creek, groan or click than it's not a KJ.

Author:	4WheelAholic [ Wed May 20, 2009 9:34 pm ]
Post subject:
If your gonna do some soaking I would use Tri-Flo instead of WD40 as it is not a silicone based lubricant unless someone has a reason not to use that one. Here is some info on it. Tri-Flow Superior Lubricant provides twice the lubricating power of most competitive brands. Its light viscosity allows for deep penetration into hard to reach moving parts. High grade petroleum oils provide optimum lubrication under extreme temperatures (-60 to 475F) and humidity. Formulated solvents soften and remove dirt and contaminants, while special additives displace moisture and prevent rust and corrosion. USAGE: • Ideal for loosening rusted and corroded nuts and bolts • Excellent for lubricating chains and all pivot points RECOMMENDED CONDITIONS: • Ideal for all conditions - wet, dry, road and trail

Author:	2006 KJ [ Wed May 20, 2009 9:38 pm ]
Post subject:
interesting.. never heard of that one. i'm always iffy on using petroleum based stuff on anything with rubber.. since it eats away at the rubber... i'm a little more easy about WD-40 since it's all natural and doesnt seem to harm things i put it on.

Author:	LIV42DY [ Wed May 20, 2009 9:59 pm ]
Post subject:
Just keep in mind that WD 40 was designed as a Moisture repelant it is not a long term lubricant.

Author:	tommudd [ Wed May 20, 2009 10:17 pm ]
Post subject:
Have you jacked it up yet to check everything , upper/ lower ball joints, bearings ??

Author:	2006 KJ [ Wed May 20, 2009 10:28 pm ]
Post subject:
tommudd wrote: Have you jacked it up yet to check everything , upper/ lower ball joints, bearings ?? nope... how do you check for balljoints.. jack it up so the tire off the ground grab it and see if it tilts in/out?

Author:	Guest [ Wed May 20, 2009 11:15 pm ]
Post subject:
on your Jeep and KJs in particular Jack it up by the LCA push in at the top of the wheel and use a 2x4 or something else long to pry the tire upward. First test, for uppers, 2nd test, for lowers.

Author:	Jeep4me99 [ Thu May 21, 2009 6:16 am ]
Post subject:
2006 KJ wrote: tommudd wrote: Have you jacked it up yet to check everything , upper/ lower ball joints, bearings ?? nope... how do you check for balljoints.. jack it up so the tire off the ground grab it and see if it tilts in/out? have a buddy grab your balljoint. then cough...deep cough. Finish by drinking many beers to forget said balljoint checking.... there are how to articles in the tech section.

Author:	Sport [ Thu May 21, 2009 8:19 am ]
Post subject:
I redid my front end a few months ago which resulted in a squeek and a rattle. The rattle or clacking turned out to be the top nut on the strut assembly not tightened all the way. The squeek was the new springs rubbing on the internal spacers and once everything settled it went away, but it made the noise when driving on almost every surface. so maybe it is one of your suspension components.

Author:	Xodius [ Thu May 21, 2009 6:26 pm ]
Post subject:
eak. I am both glad to be on this board and a bit afraid at times, lol. I have a nice click noise in my front drivers side. Usually happens after I change directions...meaning, after I pull into the garage I back up and hear it. When I get to the street and throw it in drive I hear it as I pull forward and same goes for when I am at work. I have grown accustomed to it so I do not hear it anymore but now I might have to check that out too when I am swapping out the rotors this weekend. FUN FUN.

Page 1 of 1	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/

Author:	Cali KJ [ Thu May 21, 2009 11:06 pm ]
Post subject:
2006 KJ wrote: interesting.. never heard of that one. i'm always iffy on using petroleum based stuff on anything with rubber.. since it eats away at the rubber... i'm a little more easy about WD-40 since it's all natural and doesnt seem to harm things i put it on. Have the CREEEEEK from hell here too. Narrowed mine down to the sway bar bushings. They are fairly new bushings and thought it would go away. 8K later... and a little silicon spray. hahahaha even worse!!!! So why no petroleum based stuff? I was thinking a little Vaseline or something of the sort. Is this not a good idea?

Author:	2006 KJ [ Thu May 21, 2009 11:56 pm ]
Post subject:
Cali KJ wrote: 2006 KJ wrote: interesting.. never heard of that one. i'm always iffy on using petroleum based stuff on anything with rubber.. since it eats away at the rubber... i'm a little more easy about WD-40 since it's all natural and doesnt seem to harm things i put it on. Have the CREEEEEK from hell here too. Narrowed mine down to the sway bar bushings. They are fairly new bushings and thought it would go away. 8K later... and a little silicon spray. hahahaha even worse!!!! So why no petroleum based stuff? I was thinking a little Vaseline or something of the sort. Is this not a good idea? after a couple days mine has decreased quite a bit.. and it has come and gone before. putting 'oil' on rubber wears it down/weakens it it over time.