| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| code p0500 Speed Sensor http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=46934 |
Page 1 of 1 |
| Author: | ohv_kj [ Mon Oct 05, 2009 11:34 am ] |
| Post subject: | code p0500 Speed Sensor |
for a buddies jeep... his speedo went bad... he replaced the axle sensor and the two in the front and rear of the tranny... still same code any ideas? |
|
| Author: | Hood297 [ Mon Oct 05, 2009 3:01 pm ] |
| Post subject: | |
disconnect the battery for a while? |
|
| Author: | Prospect62 [ Mon Oct 05, 2009 3:30 pm ] |
| Post subject: | |
Does the speedo work now where it wasn't working before? If so, you know you fixed the problem. The codes just need to be reset. Disconnecting the battery may work, but the better way would be to pickup a cheap code scanner (good to have in the toolbox anyway) and clear it legitimately. http://tiny.cc/QXafg |
|
| Author: | tjkj2002 [ Mon Oct 05, 2009 9:45 pm ] |
| Post subject: | |
Check the wiring at the rear diff sensor,they like to fray inside the connector. |
|
| Author: | ohv_kj [ Tue Oct 06, 2009 3:18 pm ] |
| Post subject: | |
i have a scanner. and yes the code has been cleadred...that dosen't matter though because if it was the sensor the speedo would be working again anyways even befor a cleared light... I'll get him over tonight and check the wiring...so the connector of the rear diff all the way up to where it enters the body? |
|
| Author: | tjkj2002 [ Tue Oct 06, 2009 8:46 pm ] |
| Post subject: | |
ohv_kj wrote: i have a scanner. and yes the code has been cleadred...that dosen't matter though because if it was the sensor the speedo would be working again anyways even befor a cleared light... I'll get him over tonight and check the wiring...so the connector of the rear diff all the way up to where it enters the body? Yeah check all that wiring and more so check the wires where they enter the connector that plugs into the diff sensor.
|
|
| Author: | ramlebliberty [ Tue Oct 06, 2009 10:33 pm ] |
| Post subject: | |
James, give me a call if you need to come test the lines out. I got a bag full of test equipment and no equipment to test since my truck got gutted for repairs. shouldn't be difficult to see where the fault is, Probally can refurb it too. |
|
| Author: | turbobike [ Wed Oct 07, 2009 7:47 am ] |
| Post subject: | clearing ABS code |
no message |
|
| Author: | turbobike [ Wed Oct 07, 2009 7:50 am ] |
| Post subject: | clearing ABS code |
FYI Most "el cheapo" scanners only work on engine codes. They won't clear ABS or airbag codes |
|
| Author: | ohv_kj [ Thu Oct 08, 2009 2:31 pm ] |
| Post subject: | Re: clearing ABS code |
turbobike wrote: FYI
Most "el cheapo" scanners only work on engine codes. They won't clear ABS or airbag codes trust me, my scanner is not el-cheapo... so i found that the wires close to the diff sensor have had a soderd peices to them... is that factory? the jeep was bought at 50,000 miles... could this be the prob? |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|