| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Dented Floor Board http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=60047 |
Page 1 of 1 |
| Author: | Fulltimer [ Sun Apr 10, 2011 4:44 am ] |
| Post subject: | Dented Floor Board |
I was crawling over a stretch of broken cement slabs and came down pretty hard on a piece. The result was I now have a slight hump in the floor on the drivers side front. I was thinking of putting a piece 2X6 on the hump and beating it back down with a heavy hammer. Any other suggestions? Terry PS: I made it over the offending cement just fine! 
|
|
| Author: | KJ Willy [ Sun Apr 10, 2011 10:26 am ] |
| Post subject: | Re: Dented Floor Board |
Terry, let's see how the hump is? Did the piece of concrete hit it or did it shove something else up and make the hump? |
|
| Author: | JJsTJ [ Sun Apr 10, 2011 11:18 am ] |
| Post subject: | Re: Dented Floor Board |
i have the same problem but it was a nice rock that snuck up in there. i decided to leave it alone, reminds me to watch for those loose rocks that like to roll around underneath. |
|
| Author: | Sir Sam [ Sun Apr 10, 2011 2:51 pm ] |
| Post subject: | Re: Dented Floor Board |
Get a Hammer. |
|
| Author: | Fulltimer [ Sun Apr 10, 2011 5:42 pm ] |
| Post subject: | Re: Dented Floor Board |
KJ Willy wrote: Terry, let's see how the hump is? Did the piece of concrete hit it or did it shove something else up and make the hump? The concrete did it. If I took a picture it wouldn't exactly show up. I can feel it. It just made a small bump on the floor. Terry |
|
| Author: | Fulltimer [ Sun Apr 10, 2011 5:43 pm ] |
| Post subject: | Re: Dented Floor Board |
Sir Sam wrote: Get a Hammer. I got a big hammer... a BFH to be exact! But the bump is a little bigger than the hammer head. Terry |
|
| Author: | Sir Sam [ Sun Apr 10, 2011 8:31 pm ] |
| Post subject: | Re: Dented Floor Board |
Fulltimer wrote: Sir Sam wrote: Get a Hammer. I got a big hammer... a BFH to be exact! But the bump is a little bigger than the hammer head. Terry Use a board, I use hammers and boards quite a bit when working on vehicles. |
|
| Author: | Liberty02sport [ Sun Apr 10, 2011 11:38 pm ] |
| Post subject: | Re: Dented Floor Board |
Don't use a board.....Wood is soft and dents easily compared to metal. Get a piece of flat steel a bit bigger than the size of the dent you're trying to remove then place that piece of steel on your floor jack and jack it up against the floor. You now have a fairly solid anvil to back up your hammer strikes and little chance of turning a raised dent into a lowered one. Hope this helps. 
|
|
| Author: | Fulltimer [ Tue Apr 12, 2011 8:41 am ] |
| Post subject: | Re: Dented Floor Board |
Thanks for the suggestions guys! I'll have to get around to it one of these days. Terry |
|
| Author: | JeepinJarhead03 [ Wed Apr 13, 2011 1:17 am ] |
| Post subject: | Re: Dented Floor Board |
Got a floor anchor? 
|
|
| Author: | Sir Sam [ Wed Apr 13, 2011 7:47 pm ] |
| Post subject: | Re: Dented Floor Board |
Liberty02sport wrote: Don't use a board.....Wood is soft and dents easily compared to metal. Get a piece of flat steel a bit bigger than the size of the dent you're trying to remove then place that piece of steel on your floor jack and jack it up against the floor. You now have a fairly solid anvil to back up your hammer strikes and little chance of turning a raised dent into a lowered one. Hope this helps. Perhaps you should try using some scrap 2x4's instead of balsa wood. |
|
| Author: | BugginKJ [ Wed Apr 13, 2011 9:53 pm ] |
| Post subject: | Re: Dented Floor Board |
Sir Sam wrote: Liberty02sport wrote: Don't use a board.....Wood is soft and dents easily compared to metal. Get a piece of flat steel a bit bigger than the size of the dent you're trying to remove then place that piece of steel on your floor jack and jack it up against the floor. You now have a fairly solid anvil to back up your hammer strikes and little chance of turning a raised dent into a lowered one. Hope this helps. Perhaps you should try using some scrap 2x4's instead of balsa wood. ^^^^^^^^^^^^^  x1000 |
|
| Author: | tjkj2002 [ Wed Apr 13, 2011 10:24 pm ] |
| Post subject: | Re: Dented Floor Board |
Be carefull pounding freely on the drivers floor,there is alot of wires running in that area and you could do alot more damage then what you started with. |
|
| Author: | Liberty02sport [ Thu Apr 14, 2011 2:56 am ] |
| Post subject: | Re: Dented Floor Board |
Sir Sam wrote: Liberty02sport wrote: Don't use a board.....Wood is soft and dents easily compared to metal. Get a piece of flat steel a bit bigger than the size of the dent you're trying to remove then place that piece of steel on your floor jack and jack it up against the floor. You now have a fairly solid anvil to back up your hammer strikes and little chance of turning a raised dent into a lowered one. Hope this helps. Perhaps you should try using some scrap 2x4's instead of balsa wood. Yeah ....I'll get right on that after all the body shops switch to wooden dollies to help beat metal back into shape. Metal VS. wood, Hmmm.....how does it work. Try smacking your trusty 2x4 with a 3lb. hammer, then try the same thing on a piece of 1/4 in. thick plate steel, betcha I know which one will dent first/ easiest/ etc.
|
|
| Author: | Fulltimer [ Thu Apr 14, 2011 4:05 am ] |
| Post subject: | Re: Dented Floor Board |
A piece of 2x4 would work. The wires run down a channel, on the left side if I remember right so they are not in the way. If it was something from back in the 30's or something, when they put good thick metal in cars, then I wouldn't use wood. Terry |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|