LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

thread size of factory trans cooler?
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=76384		 Page 1 of 1
Author:  Jeepin'WNC [ Mon Aug 19, 2013 7:55 am ]
Post subject:  thread size of factory trans cooler?
My trans temp light recently came on as I topped a steep grade. (on highway) My KJ is due for it third trans fluid and filter change. I picked up a trans filter kit, fluid, and a trans cooler, and I'm hoping a alleviate any future trans temp problems, and keep my transmission alive... I would like to keep my factory installed transmission cooler, and mount the after market one above it. I would like to keep the factory installed transmission line going to the factory installed trans cooler as is, then route fluid coming from the factory installed cooler to the aftermarket cooler with a male thread to barb adapter, using the rubber line that came with the aftermarket cooler then out of the aftermarket cooler back to the factory installed. The cooler I bought is a Hayden 404. I can tell you for certain that the thread size of the factory installed trans cooler is not 3/8" NPT.... My Jeep is a 2005 Renegade with the 3.7 and the 42rle trans...
Author:  Ted15 [ Mon Aug 19, 2013 11:48 am ]
Post subject:  Re: thread size of factory trans cooler?
Jeepin'WNC wrote:
My trans temp light recently came on as I topped a steep grade. (on highway) My KJ is due for it third trans fluid and filter change. I picked up a trans filter kit, fluid, and a trans cooler, and I'm hoping a alleviate any future trans temp problems, and keep my transmission alive... I would like to keep my factory installed transmission cooler, and mount the after market one above it. I would like to keep the factory installed transmission line going to the factory installed trans cooler as is, then route fluid coming from the factory installed cooler to the aftermarket cooler with a male thread to barb adapter, using the rubber line that came with the aftermarket cooler then out of the aftermarket cooler back to the factory installed. The cooler I bought is a Hayden 404. I can tell you for certain that the thread size of the factory installed trans cooler is not 3/8" NPT.... My Jeep is a 2005 Renegade with the 3.7 and the 42rle trans...


I don't know if it's the same as a KK but that external cooler on mine is for the power steering. My transmission cooler is part of the A/C condenser. :2cents:
Author:  Jeepin'WNC [ Mon Aug 19, 2013 1:14 pm ]
Post subject:  Re: thread size of factory trans cooler?
Thanks Ted! I was almost certain what I was trying to tap into was my factory installed trans cooler, now I know for certain that it is; I traced the lines from the trans directly to the cooler. I just ordered the Hayden trans line fitting kit # 390 from a local parts store; I hope these are the correct fittings for what I'm trying to accomplish...If not, they said I could return them..I was hoping to have the cooler installed yesterday, and avoid having to order fittings...Oh well, the fittings I ordered will arrive in the morning and tomorrow is my day off from work...
Author:  Ted15 [ Mon Aug 19, 2013 2:19 pm ]
Post subject:  Re: thread size of factory trans cooler?
Jeepin'WNC wrote:
Thanks Ted! I was almost certain what I was trying to tap into was my factory installed trans cooler, now I know for certain that it is; I traced the lines from the trans directly to the cooler. I just ordered the Hayden trans line fitting kit # 390 from a local parts store; I hope these are the correct fittings for what I'm trying to accomplish...If not, they said I could return them..I was hoping to have the cooler installed yesterday, and avoid having to order fittings...Oh well, the fittings I ordered will arrive in the morning and tomorrow is my day off from work...


There's a mechanical fan that comes on a KK with the tow package. Maybe you could put something like that on as well. I think it's listed as a viscous fan.
Author:  TwoBobsKJ [ Tue Aug 20, 2013 3:41 pm ]
Post subject:  Re: thread size of factory trans cooler?
I think you'd be better off installing an in-radiator cooler rather than a 2nd external cooler - it prevents the spikes that the external cooler can't help, especially if your Jeep is moving slowly or not at all.

You can swap out your current radiator for one for an '02 and it will come with the side tank for the in-rad cooler. Do essentially the same as you're planning with a 2nd external cooler - cut the top trans cooler line and run it into the top of the rad cooler, splice the outlet of the rad cooler into the line you previously cut and you're done. Here's what it looks like:

Image

Bob
Author:  Jeepin'WNC [ Fri Aug 23, 2013 2:36 pm ]
Post subject:  Re: thread size of factory trans cooler?
I've been looking into adding a '02 radiator as well. Any drawbacks/negatives to doing that as well? I found that a recycler near me has a rear-ended '02 KJ with lots of good parts...They are asking $85 for the radiator. I figure if they can give me some sort of warranty that it holds pressure, then have it pressure tested/cleaned at a local radiator shop. It would also be a perfect time to drain/refill my coolant... I finally got the trans cooler installed, and was able to use the factory cooler as well. None of the fittings I purchased, or the one that came with the cooler fit. I ended up using a fitting that I pulled from an old carb to come out of the factory cooler. I thought I'd found a fitting that fit the return line to the trans, but it didn't; it was very close and I ended up cross-threading the factory fitting. That left me with two options, cut the factory soft line and purchase bar fitting, or cut the factory hard line, and use a hose clamp. I chose the later. I've checked it for leaks, and topped off the fluid level, everything seems fine...
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/