LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

OME Ride Quality, OEM Height
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=80552		 Page 1 of 1
Author:  65Corvair [ Mon Nov 03, 2014 12:19 am ]
Post subject:  OME Ride Quality, OEM Height
At 150,000 miles my girlfriend's 02 is due for new springs and shocks. She likes the ride quality of my lifted CRD but she wants to keep the stock ride height. Would using 2925 (front) and 2947 (rear) be a good combination for keeping stock height?
Author:  Gageraid [ Mon Nov 03, 2014 1:46 am ]
Post subject:  Re: OME Ride Quality, OEM Height
It'll look lifted even with stock new springs. The ones that are on there now have sagged a few inches. :wink:
Author:  tommudd [ Mon Nov 03, 2014 2:49 am ]
Post subject:  Re: OME Ride Quality, OEM Height
I'm sure she has to be below new stock height at least an inch so like mentioned above even with stock sproings she will gain some. With 925s I would say she'll gain 3/4 (an inch at most) over new stock Stock rating was 310, 925s are 350 so a little stiffer spring rate and much better ride.
Since she has an 02 stock would of been 19.75-20 depending, with OME 925s possibly around 20.75
Not many have taken that route
Author:  65Corvair [ Tue Nov 04, 2014 11:47 am ]
Post subject:  Re: OME Ride Quality, OEM Height
What about using new Mopar springs with the OME shocks?
This would give the stock ride height certainly, but I am unsure on how this will effect the ride quality. I would be willing to try this if it is not a terrbile idea.
Author:  tommudd [ Tue Nov 04, 2014 12:46 pm ]
Post subject:  Re: OME Ride Quality, OEM Height
Personally would never waste any money on stock Mopar springs. Ride is so much better with OME or ironman springs and shocks.

So you think she would really notice an inch or so over new stock height?
Author:  Bmxer524 [ Tue Nov 04, 2014 2:05 pm ]
Post subject:  Re: OME Ride Quality, OEM Height
If she likes how yours rides, you might just be better off getting the 927.948 combo. Or at the very least 926 fronts.

She'll sit 2.5" over new stock(she might not notice). Just be honest and tell her if she wants the ride you have, she needs to have a small lift.
Author:  65Corvair [ Tue Nov 04, 2014 11:47 pm ]
Post subject:  Re: OME Ride Quality, OEM Height
She is literally 5 feet tall, she will notice any change in ride height. I will go with OME 947 in the rear, but should I go with 925 or 926 springs to keep the front end level with the back?
Author:  tommudd [ Wed Nov 05, 2014 8:37 am ]
Post subject:  Re: OME Ride Quality, OEM Height
Just go 925/947 and then adjust with a small amount of clevis if you have to.
Know what you mean about having shorter spouses etc.
My wife is 5'2' , my Mother is 5 ' 82 years old with both knees replaced and climbs into mine as well
One of my experiments on getting extra height gave me 1/4 inch more lift, didn't think my wife would notice, BUT she did !! :ROTFL:
Author:  Bmxer524 [ Wed Nov 05, 2014 9:50 am ]
Post subject:  Re: OME Ride Quality, OEM Height
Luckily, I'll never have these problems. My girlfriend is 5'6"(I think :P ). She likes the lift and added height, to the point that she wants my Jeep lol.
Author:  wheeee32 [ Thu Nov 06, 2014 8:22 am ]
Post subject:  Re: OME Ride Quality, OEM Height
Go ahead and lift her's. It then allows you to put sliders on which she can use as steps. Problem solved. :ROTFL: :BANANA:
Author:  JeepMorrison [ Sat Nov 08, 2014 1:48 pm ]
Post subject:  Re: OME Ride Quality, OEM Height
I'm short guy, I'm at 4" lift and have to use my rock sliders as a step. But my kids 6, 4 and 4 can get in with no help.
Author:  Lancer [ Mon Nov 10, 2014 4:45 am ]
Post subject:  Re: OME Ride Quality, OEM Height
Alternatively, put the biggest lift on that it'll take and tell her she's shrunk:)
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/