One replacement was a reman(from auto zone) that was too short that ended up ripping itself apart and it still wiggled
The other (the one in the video) is a new cv from auto zone.
Sent from my HTC One M9 using Tapatalk
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| HELP! Front passenger axle seal + grinding http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=85352 |
Page 1 of 1 |
| Author: | JDaPP [ Fri Sep 30, 2016 11:51 am ] |
| Post subject: | HELP! Front passenger axle seal + grinding |
Driving in to work this morning I noticed a grinding sound coming from the differential area. Looking underneath there is a pretty good leak from the passenger side axle seal (showing part # 5066066aa). At this point I am just trying to limp it home so I refilled the differential but I am still getting grinding noises when I hit a bump or I turn (always just temporary and goes away when I go back to straight driving). Is it safe to drive home? Would be about 15 miles at highway speeds, or do I need to look at getting a tow? Thoughts on what could be causing the grinding? Thanks. |
|
| Author: | USPLibby [ Sat Oct 01, 2016 10:29 pm ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
Grinding from the differential is not good. Best to get a tow. I have run my Liberty without the axle shafts and propeller shaft before. It was like driving a 2wd Liberty for a few weeks. |
|
| Author: | JDaPP [ Mon Oct 03, 2016 10:27 pm ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
Got it back. Seal changed out seems to have fixed the issue, no grinding and tried selec trac and 4wd with no issues. I suspect seal was bad enough that it allowed axle shaft to rub when it hit a bump. Appreciate all the help. |
|
| Author: | JeepinJarhead03 [ Fri Oct 07, 2016 7:13 am ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
if it was pass. side, it was more likely that the intermediate shaft has worn splines and was disengaged from the cv splines causing a wobble in the shaft tearing the seal up and the subsequent slippage of the splines causing the grinding |
|
| Author: | TIJKK1220 [ Sat Oct 08, 2016 4:11 am ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
I'm having many issues from my passenger side cv also... a shop put it on a lift in neutral and at full droop the passenger side is in full bind and won't rotate freely I've replaced the cv twice in two weeks and now the seal is leaking . I've attached a video of the movement I'm getting from the pass cv... is this common movement for a worn half shaft or are things not fully seated? It feels like the clips are seated because I can't just pull everything apart but I'm not sure... http://cloud.tapatalk.com/s/57f8a97ae9bff/VIDEO0128_02.mp4 |
|
| Author: | JeepinJarhead03 [ Sat Oct 08, 2016 6:20 am ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
two things could be happening, well, two more likely things anyway, out of 3 or 4 1. the new cv is a actual new cv rather than a remanufactured cv and is not the correct length 2. the intermediate shaft splines are worn and is not engaging the cv correctly allowing it to move (3.) both |
|
| Author: | TIJKK1220 [ Sat Oct 08, 2016 8:08 am ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
One replacement was a reman(from auto zone) that was too short that ended up ripping itself apart and it still wiggled The other (the one in the video) is a new cv from auto zone. Sent from my HTC One M9 using Tapatalk |
|
| Author: | tommudd [ Sat Oct 08, 2016 5:44 pm ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
TIJKK1220 wrote: One replacement was a reman(from auto zone) that was too short that ended up ripping itself apart and it still wiggled The other (the one in the video) is a new cv from auto zone. Sent from my HTC One M9 using Tapatalk And there lies the problem. Been discussed many times over the years about not using ones from Autozone etc, they are all too short generally |
|
| Author: | JeepinJarhead03 [ Mon Oct 10, 2016 12:34 pm ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
autozone 22 29/32" (new) 22 3/4" (reman) napa 23 5/8" (reman) |
|
| Author: | TIJKK1220 [ Mon Oct 10, 2016 9:04 pm ] |
| Post subject: | Re: HELP! Front passenger axle seal + grinding |
I see, the one I'm running currently doesn't "seem" to short but it probably not helping the situation... I inspected my half shaft before and it looked to be in good shape. I'll tear her apart again soon and post my results Sent from my HTC One M9 using Tapatalk |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|