| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| berry, berry, quiet round hare! http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=28&t=2094 |
Page 1 of 1 |
| Author: | Jeepin Al [ Wed Sep 21, 2005 7:13 pm ] |
| Post subject: | berry, berry, quiet round hare! |
WHAZ_UP it very quiet on this board lately. You are most likely like me, essentially boring, except when we go off roading!!! No new subject matter, or do you think we are all talked out at this point? Or are we all out huntin' wabbit? Al |
|
| Author: | Talon 1 [ Wed Sep 21, 2005 8:30 pm ] |
| Post subject: | |
Shhhh! Weah huntin` wabbits awound heah. |
|
| Author: | Joe Jeeper [ Wed Sep 21, 2005 9:08 pm ] |
| Post subject: | Noise |
 If you want to talk about something, what do you think about this? I have a cliking kind of noise when I have the A/C on and I am in drive or reverse, looks like the belt tentioner or the A/C compressor went to dealer and of course didn't happen! Been going on since before Rausch Creek plus it's my daily driver. Have a new belt on it. Stopped worrying about it but sure don't want to loose my belt in the middle of a trail! I keep the old one with me! How's the lift going Al? Joe
|
|
| Author: | Jeepin Al [ Wed Sep 21, 2005 9:36 pm ] |
| Post subject: | Holy Fried wabitt belt |
Try this and see if it stops the noise, unbolt the two tensioner pulleys drowned them in wd 40. after they are good and clean, take the plastic one and install it backwards. The steel one you can't (I have a steel pulley and a plastic pulley on my 2002). If the noise goes away, its the tensioner. Also check the a/c pulley, I have seen those freeze also. The first time I saw that happen was on a MOPAR! Al PS the lift is waiting for parts. The Grand Cherokee front end is on back order and maybe in by next month. The 05 knuckles will be here this week. I willsee if they are truely taller. When we measured them on an 05 they were, but off the Liberty maybe a different story. I also ordered a sub frame. Its nice having connections in the parts room at a major dodge dealer! |
|
| Author: | Joe Jeeper [ Wed Sep 21, 2005 11:42 pm ] |
| Post subject: | Noise |
| Thanks for the info Al, I'll take a look at it tomorrow at work. Good Luck with that lift project, like everyone else I'm lookin' to go higher! Joe
|
|
| Author: | Guyute1210 [ Thu Sep 22, 2005 11:39 am ] |
| Post subject: | Re: Holy Fried wabitt belt |
Jeepin Al wrote: The 05 knuckles will be here this week. I willsee if they are truely taller. When we measured them on an 05 they were, but off the Liberty maybe a different story. I also ordered a sub frame. Its nice having connections in the parts room at a major dodge dealer!
Is this true for all 2005's? And in laymans terms, that means when i do lift mine, my ball joints will be at a better angle than the older models??? |
|
| Author: | Jeepin Al [ Thu Sep 22, 2005 11:58 am ] |
| Post subject: | Wabbit knuckles |
Yep, that's what it means. If I find out that the knuckles are actually taller and that the axel "hole" has not been relocated, the 2005's will be able to be lifted with out placing undue stress on the upper ball joint. Al |
|
| Author: | PeteC [ Thu Sep 22, 2005 11:08 pm ] |
| Post subject: | |
Talon 1 wrote: Shhhh! Weah huntin` wabbits awound heah.
I went to a very quiet, enjoyable family event this weekend. shhhhhhhhhhhhhhhhh 
|
|
| Author: | Guyute1210 [ Fri Sep 23, 2005 9:38 am ] |
| Post subject: | Re: Wabbit knuckles |
Jeepin Al wrote: Yep, that's what it means. If I find out that the knuckles are actually taller and that the axel "hole" has not been relocated, the 2005's will be able to be lifted with out placing undue stress on the upper ball joint.
Al WOO-HOO!!! 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|