LOST JEEPS :: View topic - Speaking of Skid Plates (MOPAR)

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

Speaking of Skid Plates (MOPAR) http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=16723	Page 1 of 1

Author:	meh_kick [ Sat Jan 20, 2007 9:25 am ]
Post subject:	Speaking of Skid Plates (MOPAR)
I've got to get a MOPAR tranny skid up under the Jeep. Anyone do this install? It appears simple enough, but any hints would be nice. I'll be crawling under there tomorrow.

Author:	rs4mtnitro [ Sat Jan 20, 2007 9:31 am ]
Post subject:
Did you get the kit with the bolts and nut zerts? And what plates did you get?

Author:	meh_kick [ Sat Jan 20, 2007 10:46 am ]
Post subject:	Some photos of kit
I'm only putting on the Transmission skid right now. The renegade came with the rest. Here are some pics (and what I assume to do with the parts). 1) Here are the parts on the parts list 2) The nut zerts (??) need to slipped into the frame 3) Then they are torqued (I assume to flare the lip and hold into place?) 4) Once the zerts are in place, remove the bolts from front skid and set the Trans skid into place. 5) Torque all 4 bolts to 25 - 30 ft-lbs. Please correct me if I have any of this wrong. I'll post pics after the install.

Author:	Albert [ Sat Jan 20, 2007 10:54 am ]
Post subject:
Just follow the directions, and it is easier to do that you think. You will need to loosen the 2 engine skid bolts as they hold both skids in place. Take it under the jeep and position it where it goes and you will see. I thought the renegade model came with full skids. I guess not?

Author:	meh_kick [ Sat Jan 20, 2007 11:10 am ]
Post subject:
I did too. Eddo pointed it out to me one time. I went back to look at the factory sticker. It showed all but the transmission skid in the group.

Author:	spoonplugger1 [ Sat Jan 20, 2007 12:25 pm ]
Post subject:
They didn't make this skid till '05. I believe you'll have to reposition the rear hole on the driver's side on the earlier rigs.

Author:	Jeepjeepster [ Sat Jan 20, 2007 1:09 pm ]
Post subject:
I put this skid on my 04. It will sandwich between the engine skid and the engine cross member. One bolt will line up there and there is no use in drilling for the other one. On the back of the skid, one hole lined up but didnt go all the way through the cross member. You could use a nut zert there, but I just drilled two holes all the way through and used some 1/4in 2.5in(I think) grade 8 bolts and put a lock nut on top of the cross member with a washer. Works out just fine.

Author:	meh_kick [ Sat Jan 20, 2007 5:33 pm ]
Post subject:
Great. Thanks guys for the tips. I hope to get this under the Jeep tomorrow. I'll take some pictures.

Author:	Liberator [ Tue Jan 23, 2007 5:13 am ]
Post subject:
Jeepjeepster wrote: How many Jeeps you own? Or are you at a dealership???

Author:	Jeepjeepster [ Tue Jan 23, 2007 10:49 am ]
Post subject:
Liberator wrote: Jeepjeepster wrote: How many Jeeps you own? Or are you at a dealership??? We have four all together. Add an 06 Grand to that pic.

Author:	tommudd [ Tue Jan 23, 2007 6:08 pm ]
Post subject:
Hey when you live in Southern Ohio/ West Virginia or Kentucky you have to have at least 4 or 5 jeeps sitting around!! They dont all have to run but they must be sitting around the yard out front!! Just kidding Jeepjeepster, but of course I grew up in Southern Ohio ( with old trucks/ 4 wheel drives/ tractors in and around "the front yard"

Author:	Liberator [ Mon Jan 29, 2007 4:06 am ]
Post subject:	Front Yard Parking
Front Yard Parking on the lawn.... at the risk of sounding politcally incorrect.... that reminds me of the stereotyping from my favorite movie last year: Crash JeepJeepster, Too bad the wheels don't all interchange for the KJ and the other Jeeps you have... I am curious what rubber you run on the other Jeeps and how you find them...

Author:	65thKJ [ Wed Jan 31, 2007 2:48 pm ]
Post subject:
How do you change the engine oil with those skids on? It looks like it will just all dump into the skid plate.

Author:	sleeve84028 [ Wed Jan 31, 2007 3:08 pm ]
Post subject:
There is a cut-away hole up front (by the oil drain plug) The trick is getting your hand out of the hole, and out of the way of the oil stream before you make a big mess.

Author:	Jeepjeepster [ Wed Jan 31, 2007 3:59 pm ]
Post subject:	Re: Front Yard Parking
Liberator wrote: Front Yard Parking on the lawn.... at the risk of sounding politcally incorrect.... that reminds me of the stereotyping from my favorite movie last year: Crash JeepJeepster, Too bad the wheels don't all interchange for the KJ and the other Jeeps you have... I am curious what rubber you run on the other Jeeps and how you find them... The 06 Grand has the stock 235/65/17 Goodyear Hp's since it only has 1200 miles on it. I run either 235/65/17 GoodYear Hp's(soon to be replaced) or 245/70/16 Yokohama Geolander A/T-S(two sets of rims). My brother has 225/75/16 Yokohama Geolander A/T +2 on his cherokee. And the Green 94 grand cheroke in that pic has 235/75/16 GoodYear RT/S. We buy most of our ties on Tirerack.com.

Author:	Jeepjeepster [ Wed Jan 31, 2007 4:00 pm ]
Post subject:
sleeve84028 wrote: There is a cut-away hole up front (by the oil drain plug) The trick is getting your hand out of the hole, and out of the way of the oil stream before you make a big mess. I never get out of the way quick enough. Oil usually ends up all over the top of the skid and all over my arm.

Author:	sleeve84028 [ Wed Jan 31, 2007 4:04 pm ]
Post subject:
I haven't changed the oil on any liberty with the tranny skid, but can you get your fingers in on the side of the skid (not using the hole?) and wiggle the drain plug loose? This is a trick I used when I worked at the fast lube place as a teenager. Saved my skin from getting burned almost every time.

Page 1 of 1	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/