go with the frankenlift and buy 2 rear spring isolators (one per side) to level out the back... and with 265/75/16's it'll come out something liek this....
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Biggest of the 2-3" lift? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=19372 |
Page 1 of 1 |
| Author: | Donnie [ Fri Apr 06, 2007 1:22 am ] |
| Post subject: | Biggest of the 2-3" lift? |
It seems like an obvious question, which of the major quality brands sits higher. The 2.5 Franken, 3 Rough Country, 2.5 Rustys? I've noticed many of the same inchage lifts, with very different stances. Then you say, well it all depends on the tire size. I'm looking to run 265/75/16s on one of these three lifts. Which one of these would you reccomend as being the biggest? I'm not into hardcare trail riding, so I'm not too worried if the tires are a tight fit. |
|
| Author: | moose [ Fri Apr 06, 2007 8:56 am ] |
| Post subject: | |
Well, I know you can get 235/85/16's (32") under a frankenlift with some bumper trimming and the pinchweld hammered.... those 265's are a lot wider though; not sure if you might need some spidertrax spacers to prevent rubbing on the inside at full lock. |
|
| Author: | tommudd [ Fri Apr 06, 2007 10:03 am ] |
| Post subject: | |
I think I would go with the frankenlift, The Rough Country I would stay away from and the Rustys while good will need some extra help to run the tires you want to run. Do it right the first time and be done with it my worthless 2 cents this morning |
|
| Author: | Eddo [ Fri Apr 06, 2007 10:50 am ] |
| Post subject: | |
Go with the Frankenlift. Sits the highest and uses high quality parts. |
|
| Author: | kolesy [ Fri Apr 06, 2007 11:16 am ] |
| Post subject: | |
But the frankenlift NEEDS to be "broken in" with some (so I have read here) pretty aggressive wheelin. Cause a lot of people here had complained about UBJ contact til til the front springs settled. You can easily run those tires with any of the other two lifts with the same amount of trimming and spending maybe $50 for extra parts to be as high as the fraken lift. Like mentioned earlier you may need some wheel spacers to kick those fat tires out a bit. I know HOOD927 is running the rough country with those size tires and has no issues with it. And I can vouch for Rusty's high quality parts too, minus his rear shocks. Hope this opinion helps in your decision. |
|
| Author: | Donnie [ Fri Apr 06, 2007 6:11 pm ] |
| Post subject: | |
Thanks guys. I'd be using wheel spacers, I think it looks a lot better with them as well. |
|
| Author: | 2006 KJ [ Sat Apr 07, 2007 11:45 am ] |
| Post subject: | |
go with the frankenlift and buy 2 rear spring isolators (one per side) to level out the back... and with 265/75/16's it'll come out something liek this....
|
|
| Author: | kolesy [ Sat Apr 07, 2007 3:07 pm ] |
| Post subject: | |
that does look good! |
|
| Author: | KY Liberty [ Sat Apr 07, 2007 6:27 pm ] |
| Post subject: | |
Looks great. Does that have the wheel spacers on it? Also, how much did you have to do about rubbing? |
|
| Author: | 2006 KJ [ Sat Apr 07, 2007 10:40 pm ] |
| Post subject: | |
yes it does have wheel spacers (spidertrax).. it rubbed at the pinch weld.. and the front of the inner fender. (with 265/75's).. however.. with a little trimming all rubbing is gone! 
|
|
| Author: | MP Jeeper [ Sat Apr 07, 2007 11:02 pm ] |
| Post subject: | Frankenlift |
2006 KJ wrote: go with the frankenlift and buy 2 rear spring isolators (one per side) to level out the back... and with 265/75/16's it'll come out something liek this....
Isolators? i've had a Frankenlift nearly a year now, pounded it pretty hard, and still the fron rides higher. Gotten used to it but i like the level look of yours. So what are the isolators, what do they do & where can i get? Appreciate the info. BTW, nice lookin' rig! 
|
|
| Author: | tommudd [ Sat Apr 07, 2007 11:11 pm ] |
| Post subject: | |
Its the rubber pads on the top and bottom of your springs, can get them from any dealer and not that expensive. Make sure you get the ones for the top though for what you need. |
|
| Author: | 2006 KJ [ Sat Apr 07, 2007 11:16 pm ] |
| Post subject: | |
tommudd wrote: Its the rubber pads on the top and bottom of your springs, can get them from any dealer and not that expensive. Make sure you get the ones for the top though for what you need.
he's right. all you do if call the dealer and tell them what you need.. (the upper rear spring isolator) i believe they were $12 a piece.. and you just have to drop the spring and slide it under the stock one already in place... makes it a bit hard to put the spring in... a compressor would be nice.. or have a buddy stand and push on the axle so theres enough room. over all it's between 1/4 to 1/2 inch of extra lift in the back over the normal frankenlift thanks! and hope this helps ya out... |
|
| Author: | MP Jeeper [ Sun Apr 08, 2007 12:02 am ] |
| Post subject: | isol8r |
TOO easy! Thanx guys. Kinda' suprised i've not heard of/read that B4. Installed my own Frankenlift w/a buddy though so know exactly the area UR talkin' about. Puttin Al's upper A's on in another week and will prbably do the isol8rs at the same time. Thanx again! |
|
| Author: | moose [ Sun Apr 08, 2007 8:55 am ] |
| Post subject: | |
2006 KJ wrote: tommudd wrote: Its the rubber pads on the top and bottom of your springs, can get them from any dealer and not that expensive. Make sure you get the ones for the top though for what you need. he's right. all you do if call the dealer and tell them what you need.. (the upper rear spring isolator) i believe they were $12 a piece.. and you just have to drop the spring and slide it under the stock one already in place... makes it a bit hard to put the spring in... a compressor would be nice.. or have a buddy stand and push on the axle so theres enough room. over all it's between 1/4 to 1/2 inch of extra lift in the back over the normal frankenlift thanks! and hope this helps ya out... with 5' of 2x4 on top of the rotor and under the controll arm mount i can get my 12 year old to open the space for the spring... |
|
| Author: | moose [ Sun Apr 08, 2007 8:58 am ] |
| Post subject: | Re: isol8r |
MP Jeeper wrote: TOO easy! Thanx guys. Kinda' suprised i've not heard of/read that B4. Installed my own Frankenlift w/a buddy though so know exactly the area UR talkin' about. Puttin Al's upper A's on in another week and will prbably do the isol8rs at the same time.
Thanx again! we've got some posts on it in the Midwest section from lift party followups. also, the a-arms at a real beach to install. you may want to ask eddo about all the fun we had yesterday... Maybe he'll take a picture of the finished product and comment on the issues |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|