| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Light Bar Question http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=29515 |
Page 1 of 1 |
| Author: | 03CDKJ [ Thu Feb 14, 2008 11:32 pm ] |
| Post subject: | Light Bar Question |
Will an 04' Renegade light bar fit my 03'? |
|
| Author: | isutherl [ Thu Feb 14, 2008 11:44 pm ] |
| Post subject: | |
it should, as far as I know |
|
| Author: | 03CDKJ [ Thu Feb 14, 2008 11:47 pm ] |
| Post subject: | |
I figured it would.... I should have asked first But I found one for 200 and couldn't resist.. I figured I could sell it if it didn't fit.... Thanks |
|
| Author: | tjkj2002 [ Fri Feb 15, 2008 12:05 am ] |
| Post subject: | |
The Renny light bar will fit on any KJ from '02-'07,even with a sunroof. Make sure it comes with all the wiring harness and switches with the new bezal for the dash.Oh and the nutzerks for the bolts that hold it to the roof. |
|
| Author: | dieselenthusiast [ Fri Feb 15, 2008 1:08 am ] |
| Post subject: | |
cdiekhans wrote: I figured it would.... I should have asked first But I found one for 200 and couldn't resist.. I figured I could sell it if it didn't fit....
Thanks Wow, where did you find one for $200? Nice find....................... |
|
| Author: | 03CDKJ [ Fri Feb 15, 2008 1:50 am ] |
| Post subject: | |
tjkj2002 wrote: The Renny light bar will fit on any KJ from '02-'07,even with a sunroof.
Make sure it comes with all the wiring harness and switches with the new bezal for the dash.Oh and the nutzerks for the bolts that hold it to the roof. Thanks for the heads up! |
|
| Author: | 03CDKJ [ Fri Feb 15, 2008 1:56 am ] |
| Post subject: | |
dieselenthusiast wrote: cdiekhans wrote: I figured it would.... I should have asked first But I found one for 200 and couldn't resist.. I figured I could sell it if it didn't fit.... Thanks Wow, where did you find one for $200? Nice find....................... http://www.daveysjeeps.com Don't call about the light bar cause it's mine 
|
|
| Author: | tonycrd [ Fri Feb 15, 2008 7:21 am ] |
| Post subject: | |
Nice find, congrets. I just paid $295 for the same thing. ( also without fitting kit or wires ). Anyway, tell them to get you the switch and bezel and the piece of wire that goes through the roof. Since you have an '03 if you are lucky the rest of the wiring is already there! See this: http://www.jeepkj.com/forum/showthread.php?t=28870 About the 'nuzerts': they cannot give you those because they are already fitted in this Rene. You might get them from a dealer but then they'll probably sell you the entire package, incluiding all wiring / switch / etc. I picked up a thing called a 'pop a nut set', comes with various sizes of nutzerts and at tool to fit them. According to the parts list the bolts that hold light bar to the roof are 6mm. Ow, just having a closer look at the parts list, seems like they've changed something. Partnr 06507782AA is called a RIVET STUD. Sounds good! 
And here's the fitting manual: http://site.justforjeeps.com/guide/82206126AB.pdf |
|
| Author: | tommudd [ Fri Feb 15, 2008 9:23 am ] |
| Post subject: | |
dieselenthusiast wrote: cdiekhans wrote: I figured it would.... I should have asked first But I found one for 200 and couldn't resist.. I figured I could sell it if it didn't fit.... Thanks Wow, where did you find one for $200? Nice find....................... I listed it in the For Sale section a while back , it was a great deal and Chris grabbed it. Note: I am not associated with Daveys Jeeps just have dealt with them and saw they had a light bar so shared with everyone |
|
| Author: | 03CDKJ [ Fri Feb 15, 2008 7:29 pm ] |
| Post subject: | |
 What a great guy that Tom is.. I've never met him, but he's helped me a bunch. Oh, and he's such a great guy, I bet he's the one that's gonna help me install it! Right Tom! 
|
|
| Author: | tommudd [ Fri Feb 15, 2008 9:37 pm ] |
| Post subject: | |
Any time you are ready, let me know, Oh and I will be in Lancaster tomorrow, Saturday, if youre around, in Athens tonight 
|
|
| Author: | tommudd [ Sat Feb 16, 2008 10:49 am ] |
| Post subject: | |
need to get ahold of Jon (jerbacher) to see if he has the outline/ pattern/directions to show where to drill, etc, he just mounted his a few weeks ago. |
|
| Author: | tjkj2002 [ Sat Feb 16, 2008 12:34 pm ] |
| Post subject: | |
tommudd wrote: need to get ahold of Jon (jerbacher) to see if he has the outline/ pattern/directions to show where to drill, etc, he just mounted his a few weeks ago. Who needs a template? just slap it up there and drill  !(J/K)
|
|
| Author: | dieselenthusiast [ Sat Feb 16, 2008 9:07 pm ] |
| Post subject: | |
tjkj2002 wrote: tommudd wrote: need to get ahold of Jon (jerbacher) to see if he has the outline/ pattern/directions to show where to drill, etc, he just mounted his a few weeks ago. Who needs a template? just slap it up there and drill !(J/K)Uhhh, you do know Troy that you’re going to install mine, right? Don’t scare me like that! 
|
|
| Author: | tommudd [ Sat Feb 16, 2008 9:11 pm ] |
| Post subject: | |
cool sounds pretty easy and straight forward then, I am ready |
|
| Author: | 03CDKJ [ Sat Feb 16, 2008 9:35 pm ] |
| Post subject: | |
tjkj2002 wrote: tommudd wrote: need to get ahold of Jon (jerbacher) to see if he has the outline/ pattern/directions to show where to drill, etc, he just mounted his a few weeks ago. Who needs a template? just slap it up there and drill !(J/K)Tom, Don't listed to Troy!!! JK
Oh and Troy What type of sealant shoud I use for the holes... |
|
| Author: | tommudd [ Sat Feb 16, 2008 9:37 pm ] |
| Post subject: | |
I have this really good glue, no holes or sealer we will just glue it on!! Cant wait to drill holes though
|
|
| Author: | 03CDKJ [ Sat Feb 16, 2008 9:44 pm ] |
| Post subject: | |
tommudd wrote: I have this really good glue, no holes or sealer we will just glue it on!!
Cant wait to drill holes though How about I bring a piece of wood and you can drill all the holes you want 
I don't like the idea of Tom drilling into my KJ with a face like this:
Ha, This ought to be good!!
|
|
| Author: | tjkj2002 [ Sat Feb 16, 2008 9:50 pm ] |
| Post subject: | |
cdiekhans wrote: tjkj2002 wrote: tommudd wrote: need to get ahold of Jon (jerbacher) to see if he has the outline/ pattern/directions to show where to drill, etc, he just mounted his a few weeks ago. Who needs a template? just slap it up there and drill !(J/K)Tom, Don't listed to Troy!!! JK Oh and Troy What type of sealant shoud I use for the holes... |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|