LOST JEEPS :: View topic

I know there has been information posted on Diff Collars before but, can anyone point me in the right direction where to find the information. I am looking to buy a diff collar from any company that will mail to Australia. Thanks for your help.

Here is a shot of my collar installed. I used a steel one and I did have to grind down the ID by the edges where the split is for it to fit snug. Since the collar is steel and the diff is aluminum I put a thin coat of JB weld on the inside of the collar. I did not have to remove my front skid as I had plenty of room to work with. I put the bolts in from the top and used a little Lock-Tite to keep them there. Mine is also manufactured by Stafford but you have to get them from a retailer as they do not sell directly to the public. Here is a link to the aluminum collar. Maybe you can email Stafford to see if they have a "down under" retailer?

http://www.staffordmfg.com/ProductDetai ... =Home.aspx

I think Gris had the collar on and managed to break a CV joint - but the Diff held.

If you watch my front end I was pretty much giving it hell at this point with lots of spinning and abrupt stoppage of the front wheels. I had to do the same shenanigans and skullduggery 4 times to get past that obstacle and only heard a little popping and creaking when backing down...nothing while going up. Linky...

http://s136.photobucket.com/albums/q173 ... I_0477.flv

I never had one of these.

Author:	GoldCoastJeepers [ Wed Jul 09, 2008 9:43 am ]
Post subject:	Diff Collars
I know there has been information posted on Diff Collars before but, can anyone point me in the right direction where to find the information. I am looking to buy a diff collar from any company that will mail to Australia. Thanks for your help.

Author:	Cobalt-60 [ Wed Jul 09, 2008 2:16 pm ]
Post subject:	Re: Diff Collars
GoldCoastJeepers wrote: I know there has been information posted on Diff Collars before but, can anyone point me in the right direction where to find the information. I am looking to buy a diff collar from any company that will mail to Australia. Thanks for your help. Read my posts here: http://www.lostjeeps.com/forum/phpBB3/vie ... highlight= and http://www.lostjeeps.com/forum/phpBB3/vie ... iff+collar Here are pics of the aluminum one: the label angle shot size comparison Sorry, no install pics, but we did have to take the Skid Row Front Skid off to be able to put it on.

Author:	modular [ Wed Jul 09, 2008 4:12 pm ]
Post subject:
Here is a shot of my collar installed. I used a steel one and I did have to grind down the ID by the edges where the split is for it to fit snug. Since the collar is steel and the diff is aluminum I put a thin coat of JB weld on the inside of the collar. I did not have to remove my front skid as I had plenty of room to work with. I put the bolts in from the top and used a little Lock-Tite to keep them there. Mine is also manufactured by Stafford but you have to get them from a retailer as they do not sell directly to the public. Here is a link to the aluminum collar. Maybe you can email Stafford to see if they have a "down under" retailer? http://www.staffordmfg.com/ProductDetai ... =Home.aspx

Author:	Cobalt-60 [ Wed Jul 09, 2008 4:32 pm ]
Post subject:
modular wrote: Here is a shot of my collar installed. I used a steel one and I did have to grind down the ID by the edges where the split is for it to fit snug. Since the collar is steel and the diff is aluminum I put a thin coat of JB weld on the inside of the collar. I did not have to remove my front skid as I had plenty of room to work with. I put the bolts in from the top and used a little Lock-Tite to keep them there. Mine is also manufactured by Stafford but you have to get them from a retailer as they do not sell directly to the public. Here is a link to the aluminum collar. Maybe you can email Stafford to see if they have a "down under" retailer? http://www.staffordmfg.com/ProductDetai ... =Home.aspx That is a good idea -- I checked here: http://www.staffordmfg.com/Distributors.aspx It shows that they have distributors in Canada and England. It 'might' be cheaper dealing with them from OZ as they are located in fellow Commonwealth Countries.

Author:	RespectMyLibertay [ Wed Jul 09, 2008 7:59 pm ]
Post subject:
Has anyone actually gone out and tried to grenade their diff after installing one of these? I'd just like to know, because the collor could be our end-all solution for the front diff problem, even if it is just for 31-32 inch tires.

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

Diff Collars http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=33989	Page 1 of 1

Author:	Inc [ Wed Jul 09, 2008 8:02 pm ]
Post subject:
I thought these were supposed to be not worth it but after reading all his info I might have to pick one of these up. Sounds to me like they work well enough. Could be a really easy and relatively cheap way to save a big headache.

Author:	modular [ Wed Jul 09, 2008 8:09 pm ]
Post subject:
If you watch my front end I was pretty much giving it hell at this point with lots of spinning and abrupt stoppage of the front wheels. I had to do the same shenanigans and skullduggery 4 times to get past that obstacle and only heard a little popping and creaking when backing down...nothing while going up. Linky... http://s136.photobucket.com/albums/q173 ... I_0477.flv

Author:	ATXKJ [ Wed Jul 09, 2008 8:18 pm ]
Post subject:
I think Gris had the collar on and managed to break a CV joint - but the Diff held.

Author:	tjkj2002 [ Wed Jul 09, 2008 9:34 pm ]
Post subject:
ATXKJ wrote: I think Gris had the collar on and managed to break a CV joint - but the Diff held. I gernaded,literly blew it apart,a outer CV joint(drivers side),the grease squirted about 4',never did find any of the balls,and I have no collar and the diff was in perfect shape. The collar may hold the diff together but it still will crack when that sudden stop happens,and unless you weld it on I doubt it will even hold the diff together and if not a 100% perfect fit may actually cause premature pinion bearing failure if over torqued(warping the pinion bearing housing).I'd say more trouble then it worth.

Author:	Jeepjeepster [ Wed Jul 09, 2008 11:22 pm ]
Post subject:
modular wrote: If you watch my front end I was pretty much giving it hell at this point with lots of spinning and abrupt stoppage of the front wheels. I had to do the same shenanigans and skullduggery 4 times to get past that obstacle and only heard a little popping and creaking when backing down...nothing while going up. Linky... http://s136.photobucket.com/albums/q173 ... I_0477.flv haha, what was that guy talking about with "He has more stuff under there than we do." Ive got a post around here somewhere with some pics of me putting it on and such. Ive stopped trying to use the search function since I cannot get it to find anything I need.

Author:	Inc [ Wed Jul 09, 2008 11:25 pm ]
Post subject:
yeah, the search function blows. i can't search for anything beyond page 1 of the results ??????

Author:	cmohr [ Wed Jul 09, 2008 11:29 pm ]
Post subject:
Yeah, this is because one of our fellow Australian KJ's grenaded his front diff a few weeks ago, and we had to pull it apart on the side of a hill. Group Buy for Australia maybe????

Author:	GoldCoastJeepers [ Thu Jul 10, 2008 4:34 am ]
Post subject:
Thankyou very much for the great information. I think a group buy for Australia is a great idea.

Author:	modular [ Thu Jul 10, 2008 5:19 am ]
Post subject:
Jeepjeepster wrote: http://s136.photobucket.com/albums/q173 ... I_0477.flv haha, what was that guy talking about with "He has more stuff under there than we do." [/quote] He was,of course, referring to the IFS GoldCoastJeepers, if you find that you are having difficulty with getting the parts let me know if I can help an any way. Be glad to!!

Author:	InCommando [ Sat Jul 12, 2008 1:10 am ]
Post subject:
I am sure you can locate a local supplier for these in Oz. Look to industrial coupling supply houses or even fluid transfer supply houses. It is a "shaft collar" or more precisly a "split shaft collar" that comes in two pieces. Get the metric equiv. of 3 9/16" & you are good to go. I got mine off the shelf locally. It is a Ruland stock # SP-57-F 3 9/16" NOMAR two-piece split shaft collar. www.ruland.com EDIT: Might start here: http://www.naismith.com.au/product/lock ... opiece.htm

Author:	2006 KJ [ Mon Jul 28, 2008 7:18 pm ]
Post subject:
i have one and still have my stock Diff.. so it's cheap insurance for me. i had a local machinist make mine... i believe it was around $30 and it's alum.

Page 1 of 1	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/

Author:	Gris [ Mon Jul 28, 2008 4:31 pm ]
Post subject:
I never had one of these.

Author:	ATXKJ [ Mon Jul 28, 2008 8:47 pm ]
Post subject:
Gris wrote: I never had one of these. My apologies - I remembered someone having problems and it took some searching to find them It was Mutt at Crozet - he twisted a CV, bent skid plates and bumpers - but the Diff held http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?p=120411#120411 scroll up for the story - but this was his comment about the collar.

Author:	Fouros [ Tue Jul 29, 2008 10:12 pm ]
Post subject:
A i have contacted the manufacturer and getting prices for singles and multiples, they only carry up to 2" bore in stock so it would be backorder shiped from the US i will let you know when i get the pricing in Gerard