| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| RR strut plate with Rusty's .75" poly spacer http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=34177 |
Page 1 of 1 |
| Author: | scarletbegonias [ Wed Jul 16, 2008 12:59 pm ] |
| Post subject: | RR strut plate with Rusty's .75" poly spacer |
I forgot...who runs this setup? I was thinking of adding the .75" poly spacers and an addtl set of rear iso's to the stock ones on the back but im wondering if this might make anything unstable (i doubt it because to non-kj enthusiasts it doesn't even look 'lifted' ..so im told.) Anyway, any thoughts? 
|
|
| Author: | jeepkj02 [ Wed Jul 16, 2008 1:41 pm ] |
| Post subject: | |
If you are running aftermarket springs, you will need daystar upper strut mount, jba sells them. Basically would make it a frankenlift. You will need jba upper control arms. EDIT: wouldn't be a good idea to keep the strut plates. You can do a clevis lift. |
|
| Author: | scarletbegonias [ Thu Jul 17, 2008 8:02 pm ] |
| Post subject: | |
So who with a lift is running this setup up front?...I remember talking to a few but can't remember who.. How is it holdin up?? |
|
| Author: | tommudd [ Thu Jul 17, 2008 8:55 pm ] |
| Post subject: | |
Why are you wanting to go that direction? Don't think you will gain much at all for the trouble |
|
| Author: | myjeepwalks [ Fri Jul 18, 2008 1:02 pm ] |
| Post subject: | |
scarletbegonias wrote: So who with a lift is running this setup up front?...I remember talking to a few but can't remember who.. How is it holdin up??
I think the member with the jeepzilla lift in his sig runs a similar set up. In another thread he says he's getting noise from somewhere and wouldn't reveal his exact set up to me. I would just add a clevis lift and the top strut plate that rusty's sells. It would be alot easier and would gain more height than that poly spacer. |
|
| Author: | scarletbegonias [ Fri Jul 18, 2008 1:12 pm ] |
| Post subject: | |
the guys that threw on the lift never heard of a clevis lift tho!  actually...everyone i have mentioned it to has never heard of it before...isn't that strange? Anyone have a link to that thread that shows how to do one? Maybe I can show these guys how to do it  without bruising their ego, of course...
|
|
| Author: | tommudd [ Fri Jul 18, 2008 1:31 pm ] |
| Post subject: | |
scarletbegonias wrote: the guys that threw on the lift never heard of a clevis lift tho!
actually...everyone i have mentioned it to has never heard of it before...isn't that strange? Anyone have a link to that thread that shows how to do one? Maybe I can show these guys how to do it without bruising their ego, of course...You need to hang around with a bunch of people that know what they are doing then!  Most people who only deal with Wranglers etc would of never heard of it cause they dont use it as a way to raise the front.
Basically unbolt the bottom of the clevis, will have to loosen the top strut plate as well. unbolt the clevis from the strut and pull it down about 3/8 of an inch or so. Lots of people use the conduit nuts as a way to make sure that you have an equal distance on both sides, use two or three on each side. Tighten everything to spec, reinstall and then you will be HIGHER!! Now go get another alignment as well. You already have the upper strut plates dont you? Tom |
|
| Author: | jeepkj02 [ Fri Jul 18, 2008 1:39 pm ] |
| Post subject: | |
You should gain 1.5" of lift with the rusty's poly spacer. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|