| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| OME to frankenlift http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=36566 |
Page 1 of 1 |
| Author: | RAYMAN975 [ Tue Oct 07, 2008 6:48 pm ] |
| Post subject: | OME to frankenlift |
so i have OME HD springs all around, 3/8" clevis in the front, 1-extra rear isolator in the rear. and i would like my front to be just a little bit higher, maybe 1/2" to 3/4". would adding the frankenlift top plate and that spacer INSIDE the assembly make it TOO tall in the front? where could i get those individual parts and what are they exactly? ill be eventually getting the ARB bumper, hopefully within the next year or even 6 months, and would like it to sit even with that bumper or would i be better off just getting a spacer plate on top of the strut assembly. how tall of one should i get? 1/4"? 3/8"? |
|
| Author: | tommudd [ Tue Oct 07, 2008 7:19 pm ] |
| Post subject: | |
with what you have now add a top plate like Rusty sells and you will gain 1/2 inch easy. Mines right there with a Frankenlift in heighth and has held my bumper for over 75000 miles. Or if you have some 1/4 flat steel I know where there is a pattern at to make one 
So build your own Frankenlift for a 100 or so or do it on the cheap with a top plate, or another suggestion SFA!!!!
|
|
| Author: | jeepkj02 [ Tue Oct 07, 2008 7:26 pm ] |
| Post subject: | |
I have the same situation, except I have OME medium springs. I will be adding a front bumper, very soon....hopefully!! 
|
|
| Author: | renegadekj [ Tue Oct 07, 2008 7:30 pm ] |
| Post subject: | |
Do what tom said! 3 ring clevis and a 1/4" top plate and you should be sitting right with a frankie like him and I. If you put the daystar plate in with the frankie spacer and a 3 ring clevis say good by to you CV's. Or do a SFA like tom said! that wil put your front end a little higher 
|
|
| Author: | DryBones [ Tue Oct 07, 2008 7:31 pm ] |
| Post subject: | |
JeepKJ02, how much lift did you end up with using the mediums? I keep thinking of going that way as I have no intention of every doing any bumper mods. Of course, I have to be able to fit MOABs with MTR's under it so I need to really make sure of things. |
|
| Author: | RAYMAN975 [ Tue Oct 07, 2008 7:31 pm ] |
| Post subject: | |
i already have a 3/8" machined ring clevis = 3 conduit nuts 
|
|
| Author: | RAYMAN975 [ Tue Oct 07, 2008 7:33 pm ] |
| Post subject: | |
renegadekj wrote: Do what tom said! 3 ring clevis and a 1/4" top plate and you should be sitting right with a frankie like him and I. If you put the daystar plate in with the frankie spacer and a 3 ring clevis say good by to you CV's. Or do a SFA like tom said! that wil put your front end a little higher
and yea, that would be awesome to find a set of rubicon d44's front and back and put them under there! only in my dreams haha
|
|
| Author: | jeepkj02 [ Tue Oct 07, 2008 8:51 pm ] |
| Post subject: | |
DryBones wrote: JeepKJ02,
how much lift did you end up with using the mediums? I keep thinking of going that way as I have no intention of every doing any bumper mods. Of course, I have to be able to fit MOABs with MTR's under it so I need to really make sure of things. Go with the HD's. You'll get more lift and if you do decide to add a bumper you wont sag as much....trust me you will, I never thought I wanted to add a bumper, but now I am!! To answer your question, I don't know how much lift I gained, but I can tell you that I am sitting 21" in the front and 23" in the rear (front center hub to bottom of fender flare). Slight clevis in the front and 1 additional rear upper isolator pad. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|