LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

HELP! UPPER BALL JOINT NUT
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=42605		 Page 1 of 1
Author:  timmyb457 [ Sun Apr 26, 2009 3:18 pm ]
Post subject:  HELP! UPPER BALL JOINT NUT
we are in the process of taking the UBJ nut off but it all keeps spinning and the nut will no longer loosen or tighten! need ideas ASAP!
Author:  Hood297 [ Sun Apr 26, 2009 3:22 pm ]
Post subject: 
stock upper a arm?
Author:  tommudd [ Sun Apr 26, 2009 3:23 pm ]
Post subject: 
Did you already knock the UBJ loose with a hammer , if so then stick a long bar back into the spring and pry down on the UCA that will seat the ball joint back in and you can loosen it
Author:  timmyb457 [ Sun Apr 26, 2009 3:31 pm ]
Post subject: 
We tried the pry bar into the spring and no change. Ball joint is still spinning.
Author:  TAHOE [ Sun Apr 26, 2009 3:31 pm ]
Post subject: 
You can also wrap a ratchet strap around top a arm to bottom aarm and pull them tight. This keeps bolt seated and gives ya both hands to work with.
Author:  RED_KJ_666 [ Sun Apr 26, 2009 3:34 pm ]
Post subject: 
Or put a wrench on it!? If I remember right there is a a spot on the end of the Ball Joint Shaft for a 10mm Wrench. Then work the ball joint nut back and forth through some penetrating fluid.
Author:  timmyb457 [ Sun Apr 26, 2009 5:12 pm ]
Post subject: 
Still nothing. We tried the straps and pry bar. All it does is spin
Author:  jeepkj02 [ Sun Apr 26, 2009 5:18 pm ]
Post subject: 
Air impact with a u-joint socket
Author:  Diggerfreek [ Sun Apr 26, 2009 5:21 pm ]
Post subject: 
sounds like it is time to either cut off the nut or I think you can use a 10mm or 8mm 1/4 socket and a wrench if the stud is like that
Author:  DryBones [ Sun Apr 26, 2009 6:47 pm ]
Post subject: 
have you PBed the nut yet? that and the pry bar should do the trick.
Author:  Guest [ Sun Apr 26, 2009 7:02 pm ]
Post subject: 
jeepkj02 wrote:
Air impact with a u-joint socket


Not even ThunderbirdJunkie's swivel 21 with his compact 3/8 drive impact will fit on that nut. It has to be done by hand.

Ditto his air ratchet.

Are you changing out the arm? If so, just pry the arm away from the knuckle, and grab the conical seat of the balljoint stud with a pair of channel locks, and then wrench away to your heart's content.

Otherwise, grab a 10mm 1/4" drive socket, shallow, and a 1/4" drive socket, hold the nut still wtih a 21mm box end wrench, and set that ratchet to tighten. That will move that sucker innere for ya!
Author:  timmyb457 [ Mon Apr 27, 2009 12:15 am ]
Post subject: 
Diggerfreek wrote:
sounds like it is time to either cut off the nut


Yeah we decided to give up. I'm gonna order new upper a arms tomorrow. We started with the rear, so now I will have a half lifted jeep for a week. I'll post a pic of the progress when I get on my computer. We heated it up and got it loose enough to tighten it back up, but not enough to get it off. Oh well, just an excuse to upgrade more parts :-)
Author:  BjBnet [ Mon Apr 27, 2009 8:00 am ]
Post subject: 
RED_KJ_666 wrote:
Or put a wrench on it!? If I remember right there is a a spot on the end of the Ball Joint Shaft for a 10mm Wrench. Then work the ball joint nut back and forth through some penetrating fluid.


did you try what Red said? That's what the end of the ball joint is for.
Found that out last week
Author:  timmyb457 [ Mon Apr 27, 2009 8:09 am ]
Post subject: 
BjBnet wrote:
RED_KJ_666 wrote:
Or put a wrench on it!? If I remember right there is a a spot on the end of the Ball Joint Shaft for a 10mm Wrench. Then work the ball joint nut back and forth through some penetrating fluid.


did you try what Red said? That's what the end of the ball joint is for.
Found that out last week




Yeah I tried that too with no luck. I'm pretty sure the threads are messed up because it will loosen to a point and then spin. I just decided to buy new a arms.
Author:  MP Jeeper [ Mon Apr 27, 2009 5:19 pm ]
Post subject: 
i had similar problem but LBJ. Check this: http://www.lostjeeps.com/forum/phpBB3/vie ... hp?t=42618

3rd one down in the thread
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/