tinting your tail lights will work , use Nite Shades from VHT. Works great , did mine over 4 years ago and still looks good, much better then them cheap looking covers that fall off!
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| tail light covers???? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=45647 |
Page 1 of 1 |
| Author: | AR4X4 [ Thu Aug 06, 2009 10:35 pm ] |
| Post subject: | tail light covers???? |
Im looking for tailight covers that are black. Ive seen people actually tint tail lights but Im not sure if it'll work with the liberty lights. I want to get the back lights to almost match the black paint. If anyone knows where I can get a precut film or tint I would like to know. Anyone done this or have pics I can see? Thanks |
|
| Author: | tommudd [ Thu Aug 06, 2009 10:40 pm ] |
| Post subject: | |
tinting your tail lights will work , use Nite Shades from VHT. Works great , did mine over 4 years ago and still looks good, much better then them cheap looking covers that fall off!
|
|
| Author: | AR4X4 [ Thu Aug 06, 2009 10:46 pm ] |
| Post subject: | |
so night shades vht worked for you. When you sprayed it on was it hard to get it all evenlly sprayed so it doesnt look like a spray paint job? I was affraid it might look funny. Have any pics? |
|
| Author: | tommudd [ Thu Aug 06, 2009 10:59 pm ] |
| Post subject: | |
Don't have any good pictures but, here's a couple , didn't do them real dark just enough to make them match a little, nice and smooth, trick is a few very light coats
If I remember I will try and get some better shots tomorrow and post em! 
|
|
| Author: | tommudd [ Thu Aug 06, 2009 11:17 pm ] |
| Post subject: | |
one can will be more than enough to do what you want. Any parts stores that sell VHT products can get it for you and it is spelled "NITE SHADES" for off highway use only
|
|
| Author: | AR4X4 [ Sat Aug 08, 2009 11:58 pm ] |
| Post subject: | |
So I found the VHT nite shades and tested it on my third brake light as my trial run. Im not sure what happened but the paint began to dry forming little cracks all over the place.  I had to sand it off and use a bit of paint thinner. Before I painted it, all I used to clean it was rubbing alcohol and a rag. Anyone have any idea whats causing it to crack? Im going to try this all again tommorow... thanks 
|
|
| Author: | tommudd [ Sun Aug 09, 2009 12:21 am ] |
| Post subject: | |
when I did mine I only washed them really good with dish soap, laid them out to get good and dry then painted with very light coats , never had a problem |
|
| Author: | Murphyman [ Sun Aug 09, 2009 12:34 am ] |
| Post subject: | |
What kind of diff cover is that Tom? I like the red. |
|
| Author: | AR4X4 [ Sun Aug 09, 2009 3:51 pm ] |
| Post subject: | |
Well I sanded down the lense and polished it till I got a good shine going. I decided to try nite shade on just a corner of the lense and sure enough it started to form cracks again. So after cleaning up that corner I found a piece of 5% tint in my garage and used that. It looks ok but I dont think the film will hold up with time. I still think nite shades is the way to go from what I have seen on other rides. Im going to try this again on my work van tail lights and see if it works then. If anyone knows what could have caused the cracking I would like to know. THANKS
|
|
| Author: | KJWildman [ Sun Aug 09, 2009 5:17 pm ] |
| Post subject: | |
Try it again with several VERY light coats. you should barely be putting any on with the first coat and then let it dry well, then a second VERY light coat .... etc. until you get it the shade you want. it takes longer this way but should turn out good. if it is checking/ crackling then it's going on too thick IMHO. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|