how else can I get the D30a out? When I had my DTT installed he pulled it out without taking off the struts
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| D30a Removal http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=46056 |
Page 1 of 1 |
| Author: | jsc7002 [ Sat Aug 22, 2009 9:42 pm ] |
| Post subject: | D30a Removal |
How do you remove the D30a? And what all needs to be done to make it just 2wd for a little bit? Thanks |
|
| Author: | Quicksilversurf917 [ Sat Aug 22, 2009 9:56 pm ] |
| Post subject: | |
and why would u want to do this? explane.... |
|
| Author: | dgeist [ Sat Aug 22, 2009 10:01 pm ] |
| Post subject: | Re: D30a Removal |
jsc7002 wrote: How do you remove the D30a? And what all needs to be done to make it just 2wd for a little bit?
Thanks Did you grenade the front diff casing on a drop? Not sure, but I'm guessing if you removed the CV shafts to the wheels and left it in 2WD, that would keep the front pumpkin from spinning. Dan |
|
| Author: | jeepkj02 [ Sat Aug 22, 2009 10:07 pm ] |
| Post subject: | Re: D30a Removal |
dgeist wrote: jsc7002 wrote: How do you remove the D30a? And what all needs to be done to make it just 2wd for a little bit? Thanks Did you grenade the front diff casing on a drop? Not sure, but I'm guessing if you removed the CV shafts to the wheels and left it in 2WD, that would keep the front pumpkin from spinning. Dan Probably have to remove the front driveshaft because that spins in 2wd drive. |
|
| Author: | dgeist [ Sat Aug 22, 2009 10:19 pm ] |
| Post subject: | Re: D30a Removal |
jeepkj02 wrote: dgeist wrote: Not sure, but I'm guessing if you removed the CV shafts to the wheels and left it in 2WD, that would keep the front pumpkin from spinning. Dan Probably have to remove the front driveshaft because that spins in 2wd drive. Errr, I would have thought taking out the CV shafts would resolve that tricky bit... The transfer case end should be free-spinning when in 2wd. |
|
| Author: | jsc7002 [ Sat Aug 22, 2009 10:27 pm ] |
| Post subject: | |
I need to pull the whole D30a, and 'i would rather not just crawl under it and start loosing bolts. |
|
| Author: | tjkj2002 [ Sat Aug 22, 2009 10:30 pm ] |
| Post subject: | |
jsc7002 wrote: I need to pull the whole D30a, and 'i would rather not just crawl under it and start loosing bolts. It's not hard..............
1-pull CV's out(drain diff 1st) 2-remove front driveshaft 3-remove 3 diff mounts(2 of the 3 will require both front LCA removal) 4-remove front diff 5-get alignment It's really that easy but will take some time. |
|
| Author: | jsc7002 [ Sat Aug 22, 2009 10:42 pm ] |
| Post subject: | |
how do I pull the CVs? |
|
| Author: | tjkj2002 [ Sat Aug 22, 2009 10:44 pm ] |
| Post subject: | |
jsc7002 wrote: how do I pull the CVs? Did you install your own lift? If you did you already know since the whole front suspension needs to be removed like the struts and knuckles.
|
|
| Author: | Inc [ Sat Aug 22, 2009 10:44 pm ] |
| Post subject: | |
pull hard. |
|
| Author: | JeepBumm68 [ Sat Aug 22, 2009 11:21 pm ] |
| Post subject: | |
its pretty easy to take out the whole front diff. get one cv axle out. the easier side was the short shaft side. then drop the diff from there |
|
| Author: | jsc7002 [ Sat Aug 22, 2009 11:21 pm ] |
| Post subject: | |
how else can I get the D30a out? When I had my DTT installed he pulled it out without taking off the struts
|
|
| Author: | tommudd [ Sun Aug 23, 2009 12:02 am ] |
| Post subject: | |
You can do it without pulling the struts did one of them that way , taking them out of the way gives you a "little" more room is all! Also I didn't remove the right side lower control arm, just loosened the bolts and moved it over a little It not hard just get under there and look and you can see what needs to go 
|
|
| Author: | JeepBumm68 [ Sun Aug 23, 2009 1:18 am ] |
| Post subject: | |
very few stuff comes off haha. it took us like 30mins to an hour to take the front compeletly out. but that was drinking beer and what not |
|
| Author: | tonycrd [ Mon Aug 24, 2009 10:31 am ] |
| Post subject: | |
jsc7002 wrote: how else can I get the D30a out?
- - - - - - (Pic from INC's sfa thread) |
|
| Author: | jsc7002 [ Mon Aug 24, 2009 12:13 pm ] |
| Post subject: | |
oh I already got it thanks to kskj for the help |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|