| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| 4.56's with 32's??? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=47193 |
Page 1 of 1 |
| Author: | dcsveen [ Wed Oct 14, 2009 10:07 pm ] |
| Post subject: | 4.56's with 32's??? |
would 4.56s be too low for 32's? they would give me plenty of power but i've got a feeling that it would be revving pretty high goin down the interstate. what do u guys think?? |
|
| Author: | tjkj2002 [ Wed Oct 14, 2009 10:11 pm ] |
| Post subject: | |
Unless you have a 2wd KJ your out of luck on 4.56 gears since no such gear set is available for the front D30A.But otherwise yes 4.56's with 32" tires would be about perfect. |
|
| Author: | dcsveen [ Wed Oct 14, 2009 11:34 pm ] |
| Post subject: | |
well that settles it i guess, 4.10s it'll have be then, thanks |
|
| Author: | riptricket [ Wed Oct 14, 2009 11:38 pm ] |
| Post subject: | |
if one were to upgrade to 4.10's... what are the advantages? |
|
| Author: | dcsveen [ Thu Oct 15, 2009 12:39 am ] |
| Post subject: | |
when you go up any noticeable amount in tire size and keep your stock 3.73s you are goin to loose both mileage and power, and your speedomoeter is gonna be off, i put on 245 75 MTRs and lost 1 or 2 MPG and i can tell a difference in the power, so goin to 4.10s (a lower gear ratio) will bring it back to around stock specs. |
|
| Author: | 2006 KJ [ Thu Oct 15, 2009 9:33 am ] |
| Post subject: | |
dcsveen wrote: when you go up any noticeable amount in tire size and keep your stock 3.73s you are goin to loose both mileage and power, and your speedomoeter is gonna be off, i put on 245 75 MTRs and lost 1 or 2 MPG and i can tell a difference in the power, so goin to 4.10s (a lower gear ratio) will bring it back to around stock specs.
plus it will let your jeep crawl slower... reduce wear an the motor/tranny/clutch... i really need to regear to 4.10's 32" mud tires, bumper, winch, subwoofer/box, steel wheels, full skids... really weighs me down and kills the power. if you have a 6 speed (came with 3.55's not 3.73's)... 4.10's will be about perfect to restore factory power. if you have an auto i think they will still be a little tall (but MUCH better then stock) |
|
| Author: | riptricket [ Thu Oct 15, 2009 11:41 am ] |
| Post subject: | |
and aren't they like $500-$1000. |
|
| Author: | jsc7002 [ Thu Oct 15, 2009 12:41 pm ] |
| Post subject: | |
riptricket wrote: and aren't they like $500-$1000.
if you shop around for the best deal yes, the gears and rebuild kits will cost you about $500-600 and then install will be about the same, I would prepare for about a $1000-1200 total price. |
|
| Author: | ohv_kj [ Fri Oct 16, 2009 9:54 am ] |
| Post subject: | |
shop here is 900.00 installed out the door |
|
| Author: | dcsveen [ Fri Oct 16, 2009 9:31 pm ] |
| Post subject: | |
$900 for both front and rear?? |
|
| Author: | tjkj2002 [ Fri Oct 16, 2009 10:28 pm ] |
| Post subject: | |
ohv_kj wrote: shop here is 900.00 installed out the door That's a killer deal if that is for both ends since the D30A 4.10's are almost $300 alone and you have to completely remove the front diff to install them and not to mention it's $200 for the 8.25 gears also.So you have about $600-$650 in parts alone,so $250-$300 for labor is a steal(and there taking it up the stupid big time).
|
|
| Author: | KJ Willy [ Fri Oct 16, 2009 10:33 pm ] |
| Post subject: | |
Ya $900 is good, I paid that just for labor. But it is well worth it. |
|
| Author: | ridenby [ Sat Oct 17, 2009 7:03 am ] |
| Post subject: | |
D30a 4.10 Yukon Gears--$188 D30a Master Install--$93 D30 Detroit TT--$364 8.25 4.10 Yukon Gears--$187 8.25 Master Install--$114 Total--$946 + shipping Thanks, Jason CCOR 706-207-4140 __________________ www.classiccityoffroad.com 706-207-4140 Pricing I found,parts only |
|
| Author: | tjkj2002 [ Sat Oct 17, 2009 8:40 am ] |
| Post subject: | |
ridenby wrote: D30a 4.10 Yukon Gears--$188 Yukon does not make D30A gears,it has been discussed before the only company that makes D30A gears is Dana/Spicer though Precision used to package Dana/Spicer D30A gears in there own box but where still stamped Dana/Spicer.
D30a Master Install--$93 D30 Detroit TT--$364 8.25 4.10 Yukon Gears--$187 8.25 Master Install--$114 Total--$946 + shipping Thanks, Jason CCOR 706-207-4140 __________________ www.classiccityoffroad.com 706-207-4140 Pricing I found,parts only |
|
| Author: | ridenby [ Sat Oct 17, 2009 11:08 am ] |
| Post subject: | |
tjkj2002 wrote: ridenby wrote: D30a 4.10 Yukon Gears--$188 Yukon does not make D30A gears,it has been discussed before the only company that makes D30A gears is Dana/Spicer though Precision used to package Dana/Spicer D30A gears in there own box but where still stamped Dana/Spicer.D30a Master Install--$93 D30 Detroit TT--$364 8.25 4.10 Yukon Gears--$187 8.25 Master Install--$114 Total--$946 + shipping Thanks, Jason CCOR 706-207-4140 __________________ www.classiccityoffroad.com 706-207-4140 Pricing I found,parts only Just reporting what the man sent me,was suprised to see yukon also,maybe they are repackageing also. |
|
| Author: | Neatus [ Sun Oct 18, 2009 11:52 am ] |
| Post subject: | |
I would make sure that the Yukon gears are for a Dana 30a and not for a regular Dana 30...... |
|
| Author: | shaggy591a [ Mon Oct 19, 2009 10:49 pm ] |
| Post subject: | |
www.justdifferentials.com has the front gears for $212, thats where I got mine from. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|