| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| TJ bumpers on KJs general question http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=49778 |
Page 1 of 1 |
| Author: | loosvelt [ Sun Jan 31, 2010 11:34 pm ] |
| Post subject: | TJ bumpers on KJs general question |
Would most TJ bumpers fit on a KJ with the proper bracket/attachment fabrication? Would most offroad fabrication shops be able to do this pretty easily? Are there any TJ bumpers that work better then others? |
|
| Author: | VoodooMann [ Mon Feb 01, 2010 2:34 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
TJ rear bumpers have the easiest bracket to modify to fit on the front. but any bumper for any vehicle if the width fits the front of the KJ could be modified or made to fit if you poured enough time money and effort into it. Any real 4x4 shop should be able to fabricate a bracket/mount for a TJ bumper. Hell, any REAL 4x4 shop could MAKE you a CUSTOM bumper. as far as which ones work better, if better is stronger, then check the thickness of the steel. I think some of the thicker ones are made by Warn, but they are very expensive when compared to stock bumpers which only cost about $50 new. |
|
| Author: | VoodooMann [ Mon Feb 01, 2010 2:36 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
As far as using a regular rear TJ bumper. After getting all the plastic off. It only took about 20 minutes to mount the TJ bumper. All I had to do was drill a few holes and bolt it on. |
|
| Author: | loosvelt [ Mon Feb 01, 2010 11:44 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
Voodoo, Did you take a look at any JK bumpers front or rear to see how they would work? |
|
| Author: | VoodooMann [ Mon Feb 01, 2010 1:43 pm ] |
| Post subject: | Re: TJ bumpers on KJs general question |
I have been wanting to look at the JK front 'stubby' bumper (the narrow one). but I haven't been able to get a good look at one. |
|
| Author: | RED_KJ_666 [ Tue Feb 02, 2010 12:04 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
Hey man I got this on order....  http://www.smittybilt.com/product/index/46.htm I hope it turns out I contacted SmittyBilt and it's 51" side to Side should fit the Libby Perfect, the same way as it looks on the JK according to my measurments. I like the Internal Winch placement and Height I think it will be Awesome..... Making brackets seems like 3 cases of Beer and 2 Weekends so it can actually be useful with The Winch on board. The best part is that it really isn't Huge $$$ to buy.
|
|
| Author: | riptricket [ Tue Feb 02, 2010 12:14 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
that is bad booty looking how much coinage? |
|
| Author: | RED_KJ_666 [ Tue Feb 02, 2010 12:28 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
around 450$ pretty much anywhere Smitty is sold |
|
| Author: | JeepinJarhead03 [ Tue Feb 02, 2010 12:48 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
that is SCHEXI how thick is that ? it looks thin, whats the weight on it, made out fo the same stuff my rear bumper is it should be about 100 lbs, my rear bumper is about 150-175ish |
|
| Author: | tjkj2002 [ Tue Feb 02, 2010 12:51 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
RED_KJ_666 wrote: Hey man I got this on order.... http://www.smittybilt.com/product/index/46.htm I hope it turns out I contacted SmittyBilt and it's 51" side to Side should fit the Libby Perfect, the same way as it looks on the JK according to my measurments. I like the Internal Winch placement and Height I think it will be Awesome..... Making brackets seems like 3 cases of Beer and 2 Weekends so it can actually be useful with The Winch on board. The best part is that it really isn't Huge $$$ to buy.You better have some stout mounts if you plan on using a winch on that. |
|
| Author: | riptricket [ Tue Feb 02, 2010 12:54 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
i agree with tjkj, but it is possible... mount inside the bumper and to the top, maybe the bottom of the bumper too! and if it doesn't work, you can sell it on ebay for a good price I bet. |
|
| Author: | riptricket [ Tue Feb 02, 2010 1:00 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
JeepinJarhead03 wrote: that is SCHEXI how thick is that ? it looks thin, whats the weight on it, made out fo the same stuff my rear bumper is it should be about 100 lbs, my rear bumper is about 150-175ish from the site... # Manufactured from 3/16 cold roll steel # 1.75" 120 wall over rider and kickers Not bAD |
|
| Author: | tjkj2002 [ Tue Feb 02, 2010 1:02 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
riptricket wrote: i agree with tjkj, but it is possible... mount inside the bumper and to the top, maybe the bottom of the bumper too! and if it doesn't work, you can sell it on ebay for a good price I bet. Oh it can be done,no doubt. |
|
| Author: | riptricket [ Tue Feb 02, 2010 1:03 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
I wonder if something like this would fit??? http://www.warn.com/truck/mounting-systems/jk_bumper.shtml 
|
|
| Author: | JeepinJarhead03 [ Tue Feb 02, 2010 1:16 am ] |
| Post subject: | Re: TJ bumpers on KJs general question |
riptricket wrote: JeepinJarhead03 wrote: that is SCHEXI how thick is that ? it looks thin, whats the weight on it, made out fo the same stuff my rear bumper is it should be about 100 lbs, my rear bumper is about 150-175ish from the site... # Manufactured from 3/16 cold roll steel # 1.75" 120 wall over rider and kickers Not bAD thicker than i thought it was - TR fronts are 1/8" outer 3/16th subframe |
|
| Author: | daspes [ Wed Feb 03, 2010 4:13 pm ] |
| Post subject: | Re: TJ bumpers on KJs general question |
riptricket wrote: I wonder if something like this would fit??? http://www.warn.com/truck/mounting-systems/jk_bumper.shtml It's been stickied in the "Bumper Thread" for the past 9 months... Quote: Still have to clean up a few things. Warn Rock Crawler Front Winch Bumper from a JK. But here's the first shots...     Mounting was not easy due to the differences with the JK style mounting. Ultimately, I decided to pull it off. due to a lack of confidence that it would survive a recovery... |
|
| Author: | riptricket [ Wed Feb 03, 2010 5:09 pm ] |
| Post subject: | Re: TJ bumpers on KJs general question |
why do you think that it would not survive? |
|
| Author: | daspes [ Wed Feb 03, 2010 6:57 pm ] |
| Post subject: | Re: TJ bumpers on KJs general question |
Th JK bumper is gusseted and braced throughout the bumper. The only way to attach it is from the bumpers 'arms' that mount to the side of the JK's frame. On the KJ, it doesn't do a very good job of sitting flush against the unibody front sub-frame, and to get the arms to mount up you must notch the sheet metal of the subframe near where the tow hooks are. all in all you have 4 bolts running through the thin metal of the subframe, I gave it a tug with a tow strap by hand, and it started to dimple the metal. Under load, IMO it would have ripped it right off through the sub-frame. A true fitting would require actual cutting, reinforcing with drilled 1/4" and gusseting the entire front end back together. Not that it is possible, just wasn't worth it to me at the time (still isn't). |
|
| Author: | RED_KJ_666 [ Wed Feb 03, 2010 11:24 pm ] |
| Post subject: | Re: TJ bumpers on KJs general question |
I'm sure I can make it Bolt up and be FULLY functional as a winch bumper. It just makes it more mine when it's finished lol. I wish I didn't have to work so much so I could actually get a wrench on it. As soon as I get my springs and top plates I'm taking vacation for a week,and when I get around to paying off the new tires and wheels I'm going to take another week off to play lol. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|