LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Frankenlift?
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=5395		 Page 1 of 1
Author:  desertkj [ Mon Jan 30, 2006 10:13 pm ]
Post subject:  Frankenlift?
I was pretty set on the Skyjacker, but now it seems like Frankenlift has a strong following here. Any particular reasons for or against either of the kits? I've been trying to research and have been lost in the sea of opinions on the internet. If you've had any personal experiences with either, they would be greatly appreciated.
Author:  Skyjump136 [ Mon Jan 30, 2006 11:13 pm ]
Post subject: 
I've had both lifts (among others). The Frankenlift is an amazing kit and that's what I'm sticking with. The other kits have given me problems...coil bind, ball joint issues, bad struts, CV issues. The Frankenlift has been rock solid since the day I put it on.
Author:  lilmatty [ Mon Jan 30, 2006 11:22 pm ]
Post subject: 
Skyjump136 wrote:
I've had both lifts (among others). The Frankenlift is an amazing kit and that's what I'm sticking with. The other kits have given me problems...coil bind, ball joint issues, bad struts, CV issues. The Frankenlift has been rock solid since the day I put it on.


What he said...
Author:  ManicMechanicJoe [ Mon Jan 30, 2006 11:55 pm ]
Post subject: 
the frankenlift was born here...parents are always more fond of their kids then somebody else's. The Frankenlift is the best lift out there because it was designed by the same guys that started this forum. No other lift kit has this kind of testing to back it up.
Author:  0311_DoC [ Mon Jan 30, 2006 11:57 pm ]
Post subject: 
well i wish they would hurry up and make a kit for the CRD.....
Author:  lilmatty [ Tue Jan 31, 2006 1:08 am ]
Post subject: 
Why don't you make one yourself? That's sorta what they did; find a lift that worked.

Besides, we can't get CRDs in CA.
Author:  0311_DoC [ Tue Jan 31, 2006 1:34 am ]
Post subject: 
i wish i had the knowledge? I am dumb to all this suspension stuff.
Author:  Guyute1210 [ Tue Jan 31, 2006 12:53 pm ]
Post subject: 
lilmatty wrote:
Besides, we can't get CRDs in CA.


So what would happen if you owned a CRD and had to move to CA? Would you have to sell it?
Author:  dirtykj [ Tue Jan 31, 2006 1:07 pm ]
Post subject: 
Guyute1210 wrote:
lilmatty wrote:
Besides, we can't get CRDs in CA.


So what would happen if you owned a CRD and had to move to CA? Would you have to sell it?


No, there are three ways to get around that.

(1) bring in a used, previously-registered vehicle with over 7500 miles on the odometer

(2) have it gifted to you

(3) buy one as a replacement vehicle for your vehicle which breaks down beyond reasonable repair while out-of-state
Author:  0311_DoC [ Tue Jan 31, 2006 2:10 pm ]
Post subject: 
Also, I forgot to ask why doesnt the Frankelift work or fit the CRD? whats the difference?
Author:  KJ04 [ Tue Jan 31, 2006 2:35 pm ]
Post subject: 
It fits, but the springs are to soft for the CRD. People are going with Daystar puck lift and RRO Combo until someone comes out with heavier front lift coils.
Author:  0311_DoC [ Tue Jan 31, 2006 2:38 pm ]
Post subject: 
so if the manufaturers know this, why cant they make a stronger spring? is it a metal composition thing? I guess i just dont get it. :oops:
Author:  Skyjump136 [ Tue Jan 31, 2006 3:21 pm ]
Post subject: 
Its not that they can't be made...there just hasn't been a manufacturer that has yet.
Author:  0311_DoC [ Tue Jan 31, 2006 3:25 pm ]
Post subject: 
well cant the people at boulder bars and OME etc... just make em stronger? or put in a request to whomever does? Or is it a supply and demand thing?
Author:  kickit_in4wheel [ Tue Jan 31, 2006 5:23 pm ]
Post subject: 
It will take a little time. The CRD is newer than the normal Liberty, and it's heavier. I would not be surprised if someone is already working on it, but these things have to be tested before they can be marketed.

Rick
Author:  Skyjump136 [ Tue Jan 31, 2006 5:32 pm ]
Post subject: 
Quote:
Or is it a supply and demand thing?
Pretty much. A manufacturer isn't going to spend $$$ on R&D if they aren't convinced they will make it back after coming to market.

If you want springs then the best thing you can do is contact the manufacturers directly and request them. If they hear from enough people you'll have your springs.

BTW, Boulder Bars does not manufacture springs. The ones they use in the Frankenlift are made by OME. So they're pretty much in the same situation...all they can do is ask.
Author:  lilmatty [ Tue Jan 31, 2006 6:43 pm ]
Post subject: 
0311: You should take the lead on this since you sound so passionate. There's a CRD section here for you to drum up internal support and there's a 'What we need' section to put out a broadcast.

The Frankenlift was done out of necessity by LOST guys. Since no prefect lift existed for the KJ they took it upon themselves to find something that worked well. And it got the heck tested out of it. Even after deployment it had gone through a mod; the original Daystar rear springs were replaced with OME.

Anyone can build a Frankenlift but AllJ offers it all assembled and with tech support.

If you want a good lift for the CRD you should take the point and find a way to make it happen.

ps: You might start with AZScout down in AZ. He's lfited and he's a hard wheelin' CRD owner.
Author:  greiswig [ Tue Jan 31, 2006 7:23 pm ]
Post subject: 
I'm using the front springs from Rocky Road Outfitters that were designed for the heavy duty bumper, and they work well on my CRD. The CRD engine is only 200 lbs. or so heavier than the V-6, so unless you have the diesel engine, a heavy bumper, and/or a winch, it's hard for me to believe that different springs would make a huge difference.

Unless you weigh what I do...
Author:  Jeepjeepster [ Tue Jan 31, 2006 8:30 pm ]
Post subject: 
Thats what i was wondering. If you have a crd why couldnt you get the same springs you would get with a gasser and the arb bumper? Of course that thing may not weigh 200lbs, i figured it would with a winch though.

Does the franken lift use spacers with taller springs in the back?
Author:  lilmatty [ Tue Jan 31, 2006 8:36 pm ]
Post subject: 
Jeepjeepster wrote:
That what i was wondering. If you have a crd why couldnt you get the same springs you would get with a gasser and the arb bumper? Of course that thing may not weigh 200lbs, i figured it would with a winch though.

Does the franken lift use spacers with taller springs in the back?


No spacers in the back. 1.5" spacers in the front.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/