I have the Teraflex bump stop currently, but I still get some gnarley rubbing up top when fully loaded.

Here's what I have: http://www.quadratec.com/products/16197_7000.htm

I need something about an inch more. Anybody know of bigger ones? Thanks!

_________________
05 CRD Limited- Frankie IIP Lift w/spacer JBA 6" springs in rear- ProComp Street Lock steel wheels - ARB Bumper- Warn M8000 w/Synthetic Line- RRO Rails/Roof Rack- 2300W Power Inverter- 4.10 gears w/ARB Air Lockers F&R- JBA A-Arms- Viar Air Compressor/Tank- RL Super Skink Sliders-JBA Steel D30S Front Diff, Non-shiny new Paint, OD Green

those are the only after market ones available for the Liberty. you could try adding some sort of block or spacer to the top of your ucas though.

If you are hitting that bad are your shocks blown possibly ?

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

Here is my idea...

_________________
http://jeepetorp.blogg.se
Anywhere SUV can go, Jeep can go further.
Go for the best, winch the rest.

really? i give those zipties 2-3 good movements before they twist/snap... perhaps a hose clamp at the very least.

Well... I had these for 1,5 years on my stock upper control arm, and they where still there when I removed them this weekend...


But they don´t fit so tight on JBAs arms, so maybe youre right... Then I buy new one for 25 dollar or so...

_________________
http://jeepetorp.blogg.se
Anywhere SUV can go, Jeep can go further.
Go for the best, winch the rest.

Thanks for the input gents. I'm gonna try your solution jeepetorp, got one of those tow bumps for $7. Need to cut and fit. I'll likely epoxy them or some such to my JVA arms. Thanks.

_________________
05 CRD Limited- Frankie IIP Lift w/spacer JBA 6" springs in rear- ProComp Street Lock steel wheels - ARB Bumper- Warn M8000 w/Synthetic Line- RRO Rails/Roof Rack- 2300W Power Inverter- 4.10 gears w/ARB Air Lockers F&R- JBA A-Arms- Viar Air Compressor/Tank- RL Super Skink Sliders-JBA Steel D30S Front Diff, Non-shiny new Paint, OD Green

ive got some big bump stops from skyjacker. i dont now if they are bigger than the teraflex but i kno they are gigantic compared to the stock ones... these things were a pain to put in. i almost thought they werent made for my kj lol

_________________
2004 Jeep Liberty Sport 4x4 3.7L
http://www.cardomain.com/ride/3817800

Skyjacker bumpstops are smaller

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

couldn't some hard rubber be epoxied onto the end of the teraflex bumpstops? This can't be that difficult to fix, can it?!

_________________
'05 Renny 6 speed
OME/Bilsteins, Spidertrax Wheel Spacers, Husky Liners all around, Gutter Guarded Grill, 1 ISO each side rear, Boilers top shims front. And a whole list of things yet to do.

hey that's cool then!!! i'll admit when i'm wrong. gotta give credit to the zip tie!!
and i guess, what's a few cents for a new ziptie huh?