Daystar 1.5 inch spacer kit
i want to make sure this will make my liberty level anyones
will help thankshttp://www.amazon.com/gp/product/B001GH ... ss_product
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Leveling kit http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=57235 |
Page 1 of 1 |
| Author: | icecold1132 [ Tue Nov 30, 2010 7:20 pm ] |
| Post subject: | Leveling kit |
Daystar 1.5 inch spacer kit i want to make sure this will make my liberty level anyones will help thankshttp://www.amazon.com/gp/product/B001GH ... ss_product |
|
| Author: | DirtyKK [ Tue Nov 30, 2010 7:21 pm ] |
| Post subject: | Re: Leveling kit |
save yourself some money and hassle with the install of that and PM Boiler to order a 3/8" strut shim. |
|
| Author: | icecold1132 [ Tue Nov 30, 2010 9:29 pm ] |
| Post subject: | Re: Leveling kit |
i don't mind ill be doing the work myself i have my own shop just want to be sure it will be level |
|
| Author: | JeepMorrison [ Tue Nov 30, 2010 10:26 pm ] |
| Post subject: | Re: Leveling kit |
daystar spacer kit is crap....get the shims...it WILL be Level...promise |
|
| Author: | NW Reign [ Wed Dec 01, 2010 2:06 am ] |
| Post subject: | Re: Leveling kit |
So you would need 4 shims each side to equal 1.5 lift of the Daystar? What is the cost of 8 shims? Is it ok to put that many on there? |
|
| Author: | DirtyKK [ Wed Dec 01, 2010 2:19 am ] |
| Post subject: | Re: Leveling kit |
No just one pair of strut shims is needed to be level. If you put that daystar spacer in the front it would set higher in the front then the rear. |
|
| Author: | KJWildman [ Wed Dec 01, 2010 1:00 pm ] |
| Post subject: | Re: Leveling kit |
icecold1132 wrote: Daystar 1.5 inch spacer kit i want to make sure this will make my liberty level anyones will help thankshttp://www.amazon.com/gp/product/B001GH ... ss_product If you install this in the front, you will also need to install a couple rear spring isolator pads in the rear to make it level. These install IN the front spring booty'y. You will effectively being adding a 1.5" lift to the front and nothing in the rear. NW Reign wrote: So you would need 4 shims each side to equal 1.5 lift of the Daystar? What is the cost of 8 shims? Is it ok to put that many on there? NO! You can only install 1 set of these shims. These shims go on top of the spring pack between the spring and the body. There is only enough threads on the top of the spring pack to add one set ( 1 on each side ) or you won't have any threads going through to put the nuts on top. Icecold: if you are only looking to remove the slight front rake that the stock libby has, 1 set of shims should make you level. |
|
| Author: | TAHOE [ Wed Dec 01, 2010 1:49 pm ] |
| Post subject: | Re: Leveling kit |
And if boiler's shim still doesn't bring you level ( mucho sagged front springs) you can add couple conduit nuts under the front clevis to bring up slightly also. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|